Oldsmobile Recall History

General Motors LLC (GM) is recalling certain model year 1998-1999 Chevrolet Lumina and Oldsmobile Intrigue, 1997-2004 Buick Regal and Pontiac Grand Prix, 2000-2004 Chevrolet Impala, and 1998-2004 Chevrolet Monte Carlo vehicles. The affected vehicles were previously repaired under recalls 08V-118, 09V-116, and 15V-201 to address the possibility that engine oil may drip onto the hot exhaust manifold.

This defect can affect the safe operation of the airbag system. Until this recall is performed, customers should remove all items from their key rings, leaving only the ignition key. The key fob (if applicable), should also be removed from the key ring. General Motors LLC (GM) notified the agency on July 3, 2014, that they are recalling 5,877,718 model year 2000-2005 Chevrolet Impala and Monte Carlo, 1997-2003 Chevrolet Malibu, 2004-2005 Malibu Classic, 1999-2004 Oldsmobile Alero, 1998-2002 Oldsmobile Intrigue, 1999-2005 Pontiac Grand Am and 2004-2008 Pontiac Grand Prix vehicles. In these models, the weight on the key ring and/or road conditions or some other jarring event may cause the ignition switch to move out of the run position, turning off the engine.

This defect can affect the safe operation of the airbag system. Until this recall is performed, customers should remove all items from their key rings, leaving only the ignition key. The key fob (if applicable), should also be removed from the key ring. General Motors LLC (GM) notified the agency on July 3, 2014, that they are recalling 5,877,718 model year 2000-2005 Chevrolet Impala and Monte Carlo, 1997-2003 Chevrolet Malibu, 2004-2005 Malibu Classic, 1999-2004 Oldsmobile Alero, 1998-2002 Oldsmobile Intrigue, 1999-2005 Pontiac Grand Am and 2004-2008 Pontiac Grand Prix vehicles. In these models, the weight on the key ring and/or road conditions or some other jarring event may cause the ignition switch to move out of the run position, turning off the engine.

GENERAL MOTORS IS RECALLING 1,497,516 MY 1997-2003 BUICK REGAL, MY 1998-2003 CHEVROLET LUMINA, MONTE CARLO AND IMPALA, MY 1998-1999 OLDSMOBILE INTRIGUE, MY 1997-2003 PONTIAC GRAND PRIX VEHICLES EQUIPPED WITH A 3.8L V6 NATURALLY ASPIRATED ENGINE. SOME OF THESE VEHICLES HAVE A CONDITION IN WHICH DROPS OF ENGINE OIL MAY BE DEPOSITED ON THE EXHAUST MANIFOLD THROUGH HARD BRAKING.

DORMAN IS RECALLING 979 STEERING KNUCKLES, DORMAN P/NOS. 697-902 AND 697-903, SOLD UNDER DORMAN'S "OE SOLUTIONS<SUP>TM</SUP>" BRAND NAME, AND NAPA P/NOS. 7-8502 AND 7-8503 WHICH WERE SOLD FOR REPLACEMENT USE ON THE VARIOUS VEHICLES LISTED ABOVE. A POTENTIAL MATERIAL OR DESIGN DEFECT COULD RESULT IN THE STEERING KNUCKLE BREAKING IN THE HUB AREA.

DORMAN IS RECALLING 979 STEERING KNUCKLES, DORMAN P/NOS. 697-902 AND 697-903, SOLD UNDER DORMAN'S "OE SOLUTIONS<SUP>TM</SUP>" BRAND NAME, AND NAPA P/NOS. 7-8502 AND 7-8503 WHICH WERE SOLD FOR REPLACEMENT USE ON THE VARIOUS VEHICLES LISTED ABOVE. A POTENTIAL MATERIAL OR DESIGN DEFECT COULD RESULT IN THE STEERING KNUCKLE BREAKING IN THE HUB AREA.

DORMAN IS RECALLING 979 STEERING KNUCKLES, DORMAN P/NOS. 697-902 AND 697-903, SOLD UNDER DORMAN'S "OE SOLUTIONS<SUP>TM</SUP>" BRAND NAME, AND NAPA P/NOS. 7-8502 AND 7-8503 WHICH WERE SOLD FOR REPLACEMENT USE ON THE VARIOUS VEHICLES LISTED ABOVE. A POTENTIAL MATERIAL OR DESIGN DEFECT COULD RESULT IN THE STEERING KNUCKLE BREAKING IN THE HUB AREA.

K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

DORMAN PRODUCTS IS RECALLING 3,900 INTERMEDIATE STEERING SHAFTS DORMAN PART NOS. 425-151, 425-152, AND 425-153, (SOLD UNDER DORMAN'S "OE SOLUTIONS" BRAND NAME), BALKAMP #'S 7-3057, 7-3058, 7-3059 (SOLD UNDER THE "NAPA" BRAND NAME), AND PLATINUM PARTS #'S 2425151, 2425152, AND 2425153 MANUFACTURED DURING THE MONTH OF SEPTEMBER 2007. THESE REPLACEMENT STEERING SHAFTS CAN BE USED ON THE VEHICLES LISTED ABOVE. THE WELD CONNECTING THE INNER TUBE TO THE OUTER TUBE MAY BE DEFECTIVE.

GENERAL MOTORS IS RECALLING 5,862 MY 2000-2002 CHEVROLET BLAZER, MY 2000-2001 GMC JIMMY, AND MY 2000 OLDSMOBILE BRAVADA SPORT UTILITY VEHICLES. THE MULTIFUNCTION SWITCH COULD DEVELOP AN OPEN CIRCUIT CONDITION THAT RESULTS IN THE STOP LAMPS AND THE REAR HAZARD LAMPS BECOMING INOPERATIVE. THE CENTER HIGH MOUNTED STOP LAMP AND TURN SIGNAL FUNCTIONS ARE NOT AFFECTED.

CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

CERTAIN DELPHI AFTERMARKET FUEL PUMP MODULES / MODULE RESERVOIR ASSEMBLIES (MRA) THAT WERE SOLD FOR USE ON THE ABOVE LISTED VEHICLES. DURING PRODUCTION THE MRAS VENT AND FUEL RETURN TUBES WERE REVERSED. THIS CONDITION CAN RESULT IN THE VEHICLE NOT RUNNING CORRECTLY (IDLE ROUGH AND/OR STALL) DUE TO AN OVERLY RICH FUEL BLEND OR THE VEHICLE'S EVAPORATIVE EMISSION CARBON CANISTER MAY LEAK FUEL.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

CERTAIN R&B, INC. CENTRAL MULTIPORT FUEL INJECTION (CMFI) FUEL RETURN LINES, MODELS HELP 55163, NAPA BALKAMP 700-3270, AND THE CONNECTION 2560001, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE FUEL RETURN LINE HAS A MECHANICAL BLEED VALVE WHICH WAS NOT INSTALLED AT THE PROPER TORQUE.

ON CERTAIN TRUCKS AND SPORT UTILITY VEHICLES, THE DRIVER WISHING TO SIGNAL A TURN BY MOVING THE DIRECTIONAL SIGNAL LEVER, (UP OR DOWN) MAY CAUSE THE FRONT MARKER/TURN LIGHTS AND REAR TURN LIGHTS TO FLASH IN A MANNER SIMILAR TO HAZARD WARNING, RATHER THAN FLASHING ON THE DESIRED SIDE ONLY.

ON CERTAIN TRUCKS AND SPORT UTILITY VEHICLES, THE DRIVER WISHING TO SIGNAL A TURN BY MOVING THE DIRECTIONAL SIGNAL LEVER, (UP OR DOWN) MAY CAUSE THE FRONT MARKER/TURN LIGHTS AND REAR TURN LIGHTS TO FLASH IN A MANNER SIMILAR TO HAZARD WARNING, RATHER THAN FLASHING ON THE DESIRED SIDE ONLY.

ON CERTAIN MINIVANS EQUIPPED WITH SECOND-ROW BUCKET SEATS OR CAPTAIN'S CHAIRS AND A POWER SLIDING DOOR ON THE PASSENGER SIDE OF THE VEHICLE, A PASSENGER USING THE INTERIOR HANDLE TO OPEN THE POWER SLIDING DOOR COULD BE INJURED.

ON CERTAIN MINIVANS EQUIPPED WITH SECOND-ROW BUCKET SEATS OR CAPTAIN'S CHAIRS AND A POWER SLIDING DOOR ON THE PASSENGER SIDE OF THE VEHICLE, A PASSENGER USING THE INTERIOR HANDLE TO OPEN THE POWER SLIDING DOOR COULD BE INJURED.

CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, 'ACCELERATOR CONTROL SYSTEMS.' IN HOT AMBIENT CONDITIONS, THE ACCELERATOR PEDAL ARM MAY STICK AT THE ATTACHMENT TO THE BRACKET AND NOT RETURN TO THE ENGINE IDLE POSITION WHEN THE OPERATOR LIFTS HIS FOOT FROM THE ACCELERATOR PEDAL.

ON CERTAIN SPORT UTILITY VEHICLES, VIBRATION AND HEAT MAY CAUSE THE TAIL LAMP/STOP LAMP BULB TO LOOSEN IN ITS SOCKET. IF THIS OCCURS, THE BULB MAY FLICKER AND EVENTUALLY BECOME INOPERATIVE.

ON CERTAIN SPORT UTILITY VEHICLES, VIBRATION AND HEAT MAY CAUSE THE TAIL LAMP/STOP LAMP BULB TO LOOSEN IN ITS SOCKET. IF THIS OCCURS, THE BULB MAY FLICKER AND EVENTUALLY BECOME INOPERATIVE.

SOME SPORT UTILITY VEHICLES EQUIPPED WITH AN ELECTRONICALLY CONTROLLED AIR SUSPENSION (ECAS) HAVE A CONDITION IN WHICH THE ECAS MAY PRODUCE A BRIEF ELECTRICAL SPIKE WHILE THE VEHICLE IS OPERATING. THIS ELECTRICAL SPIKE CAN DISRUPT THE POWERTRAIN CONTROL MODULE (PCM) CAUSING THE VEHICLE TO STALL.

SOME SPORT UTILITY VEHICLES EQUIPPED WITH AN ELECTRONICALLY CONTROLLED AIR SUSPENSION (ECAS) HAVE A CONDITION IN WHICH THE ECAS MAY PRODUCE A BRIEF ELECTRICAL SPIKE WHILE THE VEHICLE IS OPERATING. THIS ELECTRICAL SPIKE CAN DISRUPT THE POWERTRAIN CONTROL MODULE (PCM) CAUSING THE VEHICLE TO STALL.

CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE.

CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE.

CERTAIN LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." ONE OF THE TWO SENSORS IN THE DRIVER'S AND FRONT PASSENGER'S SEAT BELT RETRACTORS COULD BE INOPERATIVE. THE SEAT BELT RETRACTORS WILL LOCK WHEN THE BELT WEBBING IS EXTRACTED DURING A CRASH; HOWEVER, THE MECHANISM THAT LOCKS THE SEAT BELT RETRACTOR WHEN THE VEHICLE DECELERATES QUICKLY, SUCH AS HEAVY BRAKING, MAY NOT OPERATE AS INTENDED.

CERTAIN LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." ONE OF THE TWO SENSORS IN THE DRIVER'S AND FRONT PASSENGER'S SEAT BELT RETRACTORS COULD BE INOPERATIVE. THE SEAT BELT RETRACTORS WILL LOCK WHEN THE BELT WEBBING IS EXTRACTED DURING A CRASH; HOWEVER, THE MECHANISM THAT LOCKS THE SEAT BELT RETRACTOR WHEN THE VEHICLE DECELERATES QUICKLY, SUCH AS HEAVY BRAKING, MAY NOT OPERATE AS INTENDED.

SOME PASSENGER VEHICLES EQUIPPED WITH 4.0L V8 ENGINES HAVE A CONDITION IN WHICH THE NYLON TUBING USED IN THE FUEL RAIL CONSTRUCTION MAY DEGRADE AND CRACK. ADDITIONALLY, THE 1995 MODEL YEAR USES A UNIQUE UNDERHOOD FUEL RETURN LINE THAT MAY CRACK. CRACKING OF THE FUEL RAIL OR RETURN LINE TUBING CAN RESULT IN A FUEL LEAK INTO THE ENGINE COMPARTMENT.

ON CERTAIN PASSENGER VEHICLES. IF THE ENGINE FAILS TO START AND THE DRIVER HOLDS THE KEY IN THE "START" POSITION FOR AN EXTENDED PERIOD, HIGH CURRENT FLOWS THROUGH THE IGNITION SWITCH, AND SOMETIMES PRODUCES ENOUGH HEAT TO MELT INTERNAL SWITCH PARTS.

CERTAIN PASSENGER VEHICLES HAVE HAZARD WARNING SWITCHES THAT MAY EXPERIENCE SOLDER JOINT CRACKING CAUSED BY RAPID TEMPERATURE TRANSITIONS AND THE SOLDERING PROCESS. IF SOLDER JOINT CRACKING OCCURS AND RESULTS IN AN OPEN CIRCUIT, THE TURN SIGNALS/HAZARD LAMPS BECOME INTERMITTENT OR INOPERATIVE.

CERTAIN PASSENGER VEHICLES HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE RETAINERS COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.

CERTAIN PASSENGER VEHICLES HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE RETAINERS COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.

CERTAIN PASSENGER VEHICLES HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE RETAINERS COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.

ON CERTAIN CADILLAC DEVILLE AND SEVILLE PASSENGER VEHICLES, FUNERAL COACHES, AND LIMOUSINES EQUIPPED WITH A V8 (4.6L) ENGINE, OLDSMOBILE AURORA PASSENGER VEHICLES EQUIPPED WITH A V8 (4.0L ) ENGINE, AND PONTIAC BONNEVILLE SSEI PASSENGER VEHICLES EQUIPPED WITH A SUPERCHARGED V6 (3.8L) ENGINE, THE FUEL TANK PRESSURE SENSORS ARE UNUSUALLY SUSCEPTIBLE TO MALFUNCTIONS. IF THE SENSOR MALFUNCTIONS, EXCESSIVE VACUUM CAN BE APPLIED DURING SELF-DIAGNOSTIC TESTING.

CERTAIN MINIVANS, PASSENGER AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEM." THE OWNER'S MANUAL DOES NOT EXPLAIN THE MEANING OF THE LOCATION SYMBOLS FOR THE CHILD RESTRAINT LOWER UNIVERSAL ANCHORAGE SYSTEM.

CERTAIN MINIVANS, PASSENGER AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEM." THE OWNER'S MANUAL DOES NOT EXPLAIN THE MEANING OF THE LOCATION SYMBOLS FOR THE CHILD RESTRAINT LOWER UNIVERSAL ANCHORAGE SYSTEM.

CERTAIN MINIVANS, PASSENGER AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEM." THE OWNER'S MANUAL DOES NOT EXPLAIN THE MEANING OF THE LOCATION SYMBOLS FOR THE CHILD RESTRAINT LOWER UNIVERSAL ANCHORAGE SYSTEM.

CERTAIN SPORT UTILITY VEHICLES WERE BUILT WITH A DRIVER'S SEAT BELT BUCKLE ASSEMBLY THAT CONTAINS AN ENERGY-ABSORBING LOOP. SUSTAINED LOADS OF SUFFICIENT MAGNITUDE AND DURATION ON THE BELT IN SEVERE CRASHES COULD FULLY DEPLOY THE BUCKLE ENERGY-ABSORBING LOOP, INTRODUCING A TOTAL OF 10 ADDITIONAL INCHES OF WEBBING INTO THE SEAT BELT SYSTEM. THE FREE FALLING LATCH PLATE USED IN THIS SYSTEM MAY ALLOW WEBBING TO DYNAMICALLY DISTRIBUTE BETWEEN THE LAP AND SHOULDER BELT AS THE DRIVER'S POSITION CHANGES DURING A MULTIPLE ROLLOVER EVENT.

ON CERTAIN MINIVANS, PICKUP TRUCKS, AND SPORT UTILITY VEHICLES WITH CERTAIN MODEL-ENGINE COMBINATIONS, THE WINDSHIELD WIPER MOTOR MAY FAIL DUE TO CRACKED SOLDER JOINTS ON THE CONTROLLER CIRCUIT BOARD. THE WINDSHIELD WIPERS COULD WORK INTERMITTENTLY OR NOT AT ALL.

CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION." THESE VEHICLES ARE EQUIPPED WITH A MECHANICAL OVERRIDE THAT COULD ALLOW THE IGNITION KEY TO BE REMOVED WITH THE SHIFT LEVER IN A POSITION OTHER THAN PARK. IN ADDITION, THESE VEHICLES HAVE AN OVERRIDE THAT CAN ALLOW THE TRANSMISSION TO BE SHIFTED OUT OF PARK WITH THE IGNITION IN THE OFF POSITION.

CERTAIN SPORT UTILITY VEHICLES WERE BUILT WITH A LEFT-FRONT BRAKE PIPE WITH A CIRCUMFERENTIAL SCORE AT A RANDOM LOCATION ALONG THE LENGTH OF THE PIPE AS THE RESULT OF THE MANUFACTURING PROCESS. IF THE BRAKE PIPE PARTIALLY OR FULLY FRACTURED, BRAKE PEDAL TRAVEL WOULD IMMEDIATELY INCREASE AND FRONT BRAKE PERFORMANCE WOULD BE REDUCED.

CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION." THESE VEHICLES ARE EQUIPPED WITH A MECHANICAL OVERRIDE THAT COULD ALLOW THE IGNITION KEY TO BE REMOVED WITH THE SHIFT LEVER IN A POSITION OTHER THAN PARK. IN ADDITION, THESE VEHICLES HAVE AN OVERRIDE THAT CAN ALLOW THE TRANSMISSION TO BE SHIFTED OUT OF PARK WITH THE IGNITION IN THE OFF POSITION.

CERTAIN SPORT UTILITY VEHICLES WERE BUILT WITH A LEFT-FRONT BRAKE PIPE WITH A CIRCUMFERENTIAL SCORE AT A RANDOM LOCATION ALONG THE LENGTH OF THE PIPE AS THE RESULT OF THE MANUFACTURING PROCESS. IF THE BRAKE PIPE PARTIALLY OR FULLY FRACTURED, BRAKE PEDAL TRAVEL WOULD IMMEDIATELY INCREASE AND FRONT BRAKE PERFORMANCE WOULD BE REDUCED.

CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARDS NO. 101, "CONTROL LOCATION, IDENTIFICATION, AND ILLUMINATION" AND NO. 208, "OCCUPANT CRASH PROTECTION." THESE VEHICLES HAVE AN INTERMITTENT CONDITION DURING VEHICLE START-UP IN WHICH THE INSTRUMENT PANEL CLUSTER MAY NOT PROPERLY POWER UP, RESULTING IN MOST OF THE DISPLAYS, TELLTALE LIGHTS, AND FUNCTIONS (EXCEPT THE SERVICE ENGINE LIGHT, TURN SIGNAL INDICATORS, AND THE INSTRUMENT PANEL CLUSTER BACKLIGHTING) BEING INOPERATIVE.

CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARDS NO. 101, "CONTROL LOCATION, IDENTIFICATION, AND ILLUMINATION" AND NO. 208, "OCCUPANT CRASH PROTECTION." THESE VEHICLES HAVE AN INTERMITTENT CONDITION DURING VEHICLE START-UP IN WHICH THE INSTRUMENT PANEL CLUSTER MAY NOT PROPERLY POWER UP, RESULTING IN MOST OF THE DISPLAYS, TELLTALE LIGHTS, AND FUNCTIONS (EXCEPT THE SERVICE ENGINE LIGHT, TURN SIGNAL INDICATORS, AND THE INSTRUMENT PANEL CLUSTER BACKLIGHTING) BEING INOPERATIVE.

CERTAIN PASSENGER VEHICLES AND MINI VANS HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE AND SOME OTHER RETAINERS USED IN VEHICLES ASSEMBLED BETWEEN JANUARY 1, 1996 AND OCTOBER 31, 1997, COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.

ON CERTAIN PASSENGER, SPORT UTILITY VEHICLES AND MINI VANS, SOME OF THESE VEHICLES HAVE A PASSENGER AIR BAG THAT WAS MANUFACTURED WITHOUT A CHECK VALVE PIN. AN AIR BAG WITHOUT THE CHECK VALVE PIN COULD PRODUCE INCREASED PRESSURE AT THE ONSET OF THE AIR BAG DEPLOYMENT AND REDUCED PRESSURE AFTERWARD.

ON CERTAIN SPORT UTILITY VEHICLES, A FUEL FILTER FITTING CAN BECOME DISCONNECTED. IF THIS WERE TO OCCUR WHILE ATTEMPTING TO START THE ENGINE, A NO-START CONDITION WOULD RESULT AND FUEL WOULD BE PUMPED OUT THE FUEL FILTER ONTO THE GROUND.

ON CERTAIN SPORT UTILITY VEHICLES, A FUEL FILTER FITTING CAN BECOME DISCONNECTED. IF THIS WERE TO OCCUR WHILE ATTEMPTING TO START THE ENGINE, A NO-START CONDITION WOULD RESULT AND FUEL WOULD BE PUMPED OUT THE FUEL FILTER ONTO THE GROUND.

CERTAIN PASSENGER, MINI VANS, AND SPORT UTILITY VEHICLES HAVE AN AIR BAG INFLATOR ON THE DRIVER'S SIDE THAT COULD FRACTURE AT A WELD DURING A DEPLOYMENT.

CERTAIN PASSENGER, MINI VANS, AND SPORT UTILITY VEHICLES HAVE AN AIR BAG INFLATOR ON THE DRIVER'S SIDE THAT COULD FRACTURE AT A WELD DURING A DEPLOYMENT.

CERTAIN PASSENGER, MINI VANS, AND SPORT UTILITY VEHICLES HAVE AN AIR BAG INFLATOR ON THE DRIVER'S SIDE THAT COULD FRACTURE AT A WELD DURING A DEPLOYMENT.

CERTAIN PASSENGER, MINI VANS, AND SPORT UTILITY VEHICLES HAVE AN AIR BAG INFLATOR ON THE DRIVER'S SIDE THAT COULD FRACTURE AT A WELD DURING A DEPLOYMENT.

CERTAIN PASSENGER, MINI VANS, AND SPORT UTILITY VEHICLES HAVE AN AIR BAG INFLATOR ON THE DRIVER'S SIDE THAT COULD FRACTURE AT A WELD DURING A DEPLOYMENT.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE MULTIFUNCTION SWITCH COULD DEVELOP AN OPEN CIRCUIT CONDITION THAT RESULTS IN THE STOP LAMPS AND THE REAR HAZARD LAMPS BECOMING INOPERATIVE. THE CENTER HIGH MOUNTED STOP LAMP AND TURN SIGNAL FUNCTIONS ARE NOT AFFECTED.

VEHICLE DESCRIPTION: CERTAIN MINI VANS BUILT WITH SECOND ROW 50/50 SPLIT BENCH SEATS OR CAPTAIN'S CHAIRS, FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." THE SEAT LATCH ANCHOR WIRE DIAMETER IS GREATER THAN 6.1 MM.

ON CERTAIN PASSENGER VEHICLES. IF THE ENGINE FAILS TO START AND THE DRIVER HOLDS THE KEY IN THE "START" POSITION FOR AN EXTENDED PERIOD, HIGH CURRENT FLOWS THROUGH THE IGNITION SWITCH, AND SOMETIMES PRODUCES ENOUGH HEAT TO MELT INTERNAL SWITCH PARTS.

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1996-1997 4-WHEEL DRIVE CHEVROLET BLAZER, GMC JIMMY, AND OLDSMOBILE BRAVADA SPORT UTILITY VEHICLES. SOME OWNERS HAVE HAD TO PAY FOR REPLACEMENT OF THE UPPER BALL JOINTS THAT HAVE SEPARATED. GM IS PROVIDING A SPECIAL POLICY TO THESE OWNERS TO COVER UPPER BALL JOINT REPLACEMENT IF THE CUSTOMER FOLLOWED THE RECOMMENDED MAINTENANCE SCHEDULE FOR THE CHASSIS LUBRICATION AND THE VEHICLE STILL REQUIRED THE REPLACEMENT OF THE UPPER BALL JOINTS DUE TO SEPARATION.

VEHICLE DESCRIPTION: 1997-2001 CHEVROLET VENTURE, PONTIAC MONTANA/TRANSPORT, AND OLDSMOBILE SILHOUETTE MINI VANS EQUIPPED WITH PASSENGER SIDE POWER SLIDING DOORS THAT WERE SERVICED IN CAMPAIGN 01013 (01V-067) FROM APRIL TO AUGUST 2001. ALSO 2001 CHEVROLET VENTURE, PONTIAC MONTANA, AND OLDSMOBILE SILHOUETTE MINI VANS EQUIPPED WITH PASSENGER SIDE POWER SLIDING DOORS ASSEMBLED IN JANUARY THROUGH APRIL 2001. THESE VEHICLES HAVE INADEQUATE FRONT WELDS. IF A FRONT WELD FAILS, THE ACTUATOR CAN JAM IN THE UNLATCHED POSITION AND, WHEN THE SLIDING DOOR CLOSES, IT WILL NOT BE LATCHED.

ON CERTAIN SPORT UTILITY VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN, AND IN THE DISTRICT OF COLUMBIA. FAILURE OF AN UPPER CONTROL ARM BALL JOINT ASSEMBLY COULD OCCUR DUE TO CORROSION.

ON CERTAIN PASSENGER VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE "SALT BELT" STATES: ALASKA, COLORADO, CONNECTICUT, DELAWARE, IDAHO, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MONTANA, NEBRASKA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, NORTH DAKOTA, OHIO, PENNSYLVANIA, RHODE ISLAND, SOUTH DAKOTA, UTAH, VERMONT, WEST VIRGINIA, WISCONSIN, AND WYOMING. IF A BUILDUP OF SNOW OR ICE RESTRICTS THE MOVEMENT OF THE PASSENGER SIDE WINDSHIELD WIPER ARM, THE PIVOT HOUSING CAN CRACK AND THE WIPERS WILL NOT OPERATE.

ON CERTAIN PASSENGER VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE "SALT BELT" STATES: ALASKA, COLORADO, CONNECTICUT, DELAWARE, IDAHO, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MONTANA, NEBRASKA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, NORTH DAKOTA, OHIO, PENNSYLVANIA, RHODE ISLAND, SOUTH DAKOTA, UTAH, VERMONT, WEST VIRGINIA, WISCONSIN, AND WYOMING. IF A BUILDUP OF SNOW OR ICE RESTRICTS THE MOVEMENT OF THE PASSENGER SIDE WINDSHIELD WIPER ARM, THE PIVOT HOUSING CAN CRACK AND THE WIPERS WILL NOT OPERATE.

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES, EQUIPPED WITH SUNVISOR LOCATED AIR BAG LABELS, FAIL TO CONFORM TO FEDERAL MOTOR VEHICLES SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THESE VEHICLES HAVE A MESSAGE AREA LESS THAN 30 CM WHICH DOES NOT MEET THE REQUIREMENTS OF THE STANDARD.

VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH PASSENGER SIDE POWER SLIDING DOORS. THE DOOR CLOSES BUT MAY NOT BE LATCHED. IF THIS HAPPENS, THE POWER SLIDING DOOR CAN OPEN WHILE THE VEHICLE IS IN MOTION, PARTICULARLY WHEN THE VEHICLE ASCENDS A HILL, MAKES A TURN, OR TRAVELS OVER A ROUGH ROAD SURFACE.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. UNDER CERTAIN CIRCUMSTANCES THE FRONT LOWER CONTROL ARM BRACKETS MAY FRACTURE. THIS FRACTURE COULD RESULT IN SEPARATION OF THE FRONT LOWER CONTROL ARM FROM THE FRAME.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. UNDER CERTAIN CIRCUMSTANCES THE FRONT LOWER CONTROL ARM BRACKETS MAY FRACTURE. THIS FRACTURE COULD RESULT IN SEPARATION OF THE FRONT LOWER CONTROL ARM FROM THE FRAME.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. CORROSION OF THE AIR BAG INFLATOR'S INTERNAL WIRING, WHICH CAN OCCUR OVER TIME, COULD CAUSE THE INADVERTENT DEPLOYMENT OF THE DRIVER'S AIR BAG. THIS DEPLOYMENT COULD OCCUR DURING VEHICLE START-UP, WHILE THE VEHICLE IS PARKED OR IDLING, OR WHILE IN OPERATION.

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES EQUIPPED WITH MANUAL TRANSAXLES (RPO M86) FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 114, "THEFT PROTECTION." WHEN A DRIVER ATTEMPTS TO SHIFT FROM 5TH GEAR TO REVERSE, A SHIFT INHIBITOR CAUSES THE TRANSMISSION TO BE MECHANICALLY IN 4TH GEAR EVEN THOUGH THE SHIFT LEVER INDICATES REVERSE GEAR.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE ENGINE STARTER FAILS TO ENGAGE AND THE DRIVER HOLD THE KEY IN THE "START" POSITION FOR AN EXTENDED PERIOD, HIGH CURRENT FLOWS THROUGH THE IGNITION SWITCH, PRODUCING HEAT THAT CAN MELT SWITCH PARTS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE REAR SHOULDER BELT(S) DO NOT RETRACT. A RETAINER COULD SEPARATE FROM A REAR SEAT SHOULDER BELT RETRACTOR WHICH RESULTS IN THE RETRACTOR RETURN SPRING BECOMING DISENGAGED.

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES. SOME OF THESE VEHICLES WERE BUILT WITH INCORRECT PAYLOAD INFORMATION ON THE VEHICLE CERTIFICATION LABEL. THE PAYLOAD SHOWN ON THE LABEL IS GREATER THAN THE MAXIMUM VALIDATED PAYLOAD. IF THE VEHICLE WERE LOADED TO THE INCORRECTLY LABELED PAYLOAD, IT MAY NOT RIDE AND HANDLE IN THE MANNER THAT THE DRIVER EXPECTS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. SOME OF THESE VEHICLES WERE BUILT WITH REAR SEAT SHOULDER BELTS THAT COULD TWIST, ALLOWING THE WEBBING TO BE JAMMED IN THE RETRACTOR. WHEN THE SHOULDER BELT WEBBING BECOMES JAMMED IN THE RETRACTOR, THE SEAT BELT BECOMES UNUSABLE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES, LIGHT DUTY TRUCKS, SPORT UTILITY VEHICLES, AND MINI VANS EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

VEHICLE DESCRIPTION: PASSENGER VEHICLES, LIGHT DUTY TRUCKS, SPORT UTILITY VEHICLES, AND MINI VANS EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

VEHICLE DESCRIPTION: PASSENGER VEHICLES. SOME OF THESE VEHICLES HAVE INTERNAL FLUID LEAKS IN THE BRAKE HYDRAULIC CONTROL UNIT.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. SOME OF THESE VEHICLES HAVE INTERNAL FLUID LEAKS IN THE BRAKE HYDRAULIC CONTROL UNIT.

VEHICLE DESCRIPTION: THESE VEHICLES DO NOT COMPLY WITH THE OCCUPANT PROTECTION REQUIREMENTS OF FMVSS NO. 201, "OCCUPANT PROTECTION IN INTERIOR IMPACT." THE CONSOLE COVER ON THESE VEHICLES DOES NOT STAY CLOSED WHEN A SPECIFIED VERTICAL LOAD IS APPLIED.

VEHICLE DESCRIPTION: MINI VANS WITH EXTENDED WHEELBASE. SOME OF THESE VEHICLES HAVE INOPERATIVE FUEL TANK ROLLOVER VALVES AND FUEL LEAKAGE WOULD EXCEED THE PERMISSIBLE AMOUNT IN A ROLLOVER TEST. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 301, "FUEL SYSTEM INTEGRITY."

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE BRAKE BOOSTER TO PEDAL ASSEMBLY ATTACHMENT NUTS MAY BE LOOSE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT FRONT BRAKE ROTOR, BRAKE CALIPER ASSEMBLY, BRAKE PADS, AND CALIPER MOUNTING BRACKET ON EITHER THE LEFT OR RIGHT SIDE OF THE VEHICLE.

VEHICLE DESCRIPTION: PASSENGER MINI VANS. THE LEFT AND/OR RIGHT FRONT LOWER INSULATOR TO CRADLE CENTER METAL SLEEVE IS COLLAPSED, WHICH CAN RESULT IN LOSS OF CLAMP LOAD IN THE JOINT. IF THE CLAMP LOAD IS REDUCED OR LOST, THE BOLT CAN BE LOST OR BROKEN AND THE JOINT CAN SEPARATE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE STEERING WHEEL CAN COME LOOSE FROM THE STEERING SHAFT BECAUSE THE STEERING WHEEL RETAINING NUT COULD HAVE BEEN IMPROPERLY TIGHTENED.

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH A 3.8L V6 ENGINE. SOME OF THESE VEHICLES WERE BUILT WITHOUT A HEATER HOSE CLIP WHICH COULD ALLOW THE HOSE TO SAG AND CONTACT THE OXYGEN SENSOR RESULTING IN A COOLANT LEAK.

VEHICLE DESCRIPTION: PASSENGER MINI VANS EQUIPPED WITH BUCKET SEATS OR A SPLIT BENCH SEAT IN THE SECOND (MIDDLE) OR THIRD (BACK) ROW. THE SEAT LATCH MECHANISMS ON BUCKET SEATS AND ON THE 40% PORTION OF THE SPLIT BENCH SEAT IN THE SECOND AND THIRD ROWS DO NOT HAVE PROTECTIVE COVERS.

VEHICLE DESCRIPTION: MINI VANS. THESE VEHICLES MAY HAVE (1) A BROKEN SHIFT CABLE FITTING OR (2) LOOSE SHIFT LINKAGE. CONSEQUENTLY, MOVING THE SHIFT LEVER TO A 'PARK' POSITION MAY NOT SHIFT THE TRANSMISSION TO 'PARK'.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE OWNER MANUALS DO NOT CONTAIN THE REQUIREMENT INFORMATION PERTAINING TO THE VEHICLE HEADLAMP AIMING DEVICE. THIS DOES NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE OWNER MANUALS DO NOT CONTAIN THE REQUIREMENT INFORMATION PERTAINING TO THE VEHICLE HEADLAMP AIMING DEVICE. THIS DOES NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

VEHICLE DESCRIPTION: PASSENGER MINI VANS EQUIPPED WITH TRACTION CONTROL SYSTEMS. THE WINDSHIELD WIPER LINKAGE ARM CAN CONTACT A BRAKE LINE WHICH IS CONNECTED TO THE TRACTION CONTROL SYSTEM MODULATOR VALVE. THIS CONTACT CAN CHAFE THE BRAKE LINE RESULTING IN A BRAKE FLUID LEAK.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES WERE BUILT WITH THE POTENTIAL FOR THE INTERIOR LAMPS TO COME ON UNEXPECTEDLY WHILE THE VEHICLES ARE BEING DRIVEN. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 101, "CONTROLS AND DISPLAYS."

VEHICLE DESCRIPTION: MULTI-PURPOSE PASSENGER VEHICLE EQUIPPED WITH 4-WHEEL DRIVE OR ALL-WHEEL-DRIVE. ONE OR BOTH OF THE ATTACHING NUTS FOR THE RIGHT-HAND LOWER CONTROL ARM ARE UNDER TORQUED. THIS CAN ALLOW THE ATTACHMENT BOLT TO LOOSEN AND SUBSEQUENT BREAK RESULTING IN SEPARATION OF THE LOWER CONTROL ARM FROM THE FRAME.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE ANTILOCK BRAKE SYSTEM (ABS) MODULATOR CAN CORRODE AND LEAK FLUID FROM THE FRONT BRAKE CIRCUIT.

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE PASSENGER VEHICLES. A FATIGUE FRACTURE OF THE REAR AXLE RIGHT-HAND BRAKE PIPE CAN OCCUR CAUSING A SLOW BRAKE FLUID LEAK RESULTING IN A SOFT BRAKE PEDAL. IF THE BRAKE PIPE BREAKS, THE DRIVER WOULD EXPERIENCE A SUDDEN DROP IN THE BRAKE PEDAL, THE INSTRUMENT PANEL BRAKE LIGHT WOULD ILLUMINATE, AND THERE WOULD BE A LOSS OF REAR BRAKE PERFORMANCE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

THE PROTECTIVE COVER FOR THE UNDERHOOD FUSE CENTER WAS OMITTED. WITHOUT THIS COVER, THE POSITIVE TERMINAL BOLT ON THE FUSE BLOCK IS EXPOSED AND CAN CONTACT THE INSULATED NEGATIVE BATTERY CABLE. IF THE INSULATION ON THE NEGATIVE CABLE BECOMES SUFFICIENTLY WORN, AN ELECTRICAL SHORT CIRCUIT CAN OCCUR BETWEEN THE POSITIVE TERMINAL AND NEGATIVE CABLE RESULTING IN EXTREMELY HIGH CURRENT FLOW.

SOME OF THESE VEHICLES HAVE A STRAINED OR SEPARATED WASHER/WIPER SWITCH POWER FEED WIRE.

SOME OF THESE VEHICLES HAVE A STRAINED OR SEPARATED WASHER/WIPER SWITCH POWER FEED WIRE.

SOME OF THESE VEHICLES HAVE A STRAINED OR SEPARATED WASHER/WIPER SWITCH POWER FEED WIRE.

THE FRONT AND/OR REAR HAZARD WARNING LAMPS (FOUR-WAY FLASHERS) DO NOT FLASH WHEN THE HAZARD SWITCH IS ACTIVATED. THIS FAILS TO COMPLY WITH FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

VEHICLE DESCRIPTION: 4-DOOR, 4-WHEEL DRIVE AND ALL-WHEEL DRIVE MULTI-PURPOSE PASSENGER VEHICLES. DURING DEVELOPMENT TESTING, THE PROP SHAFT CONTACTED THE INBOARD SIDE OF THE FUEL TANK ALLOWING FUEL LEAKAGE. THIS LEAKAGE WAS IN EXCESS OF THE AMOUNT PERMITTED BY FMVSS 301, "FUEL SYSTEM INTEGRITY."

DURING DEPLOYMENT OF THE PASSENGER AIR BAG, THE AIR BAG FABRIC CAN SNAG ON A REINFORCEMENT INSIDE THE INSTRUMENT PANEL, CAUSING THE EXPANDING AIR BAG TO LIFT THE INSTRUMENT PANEL PAD AND THEN DEPLOY UNDER THE INSTRUMENT PANEL INSTEAD OF THROUGH THE DOOR IN THE INSTRUMENT PANEL.

THESE VEHICLES EXHIBIT A CONDITION IN WHICH A REAR SEAT BELT BUCKLE RELEASE BUTTON CAN STICK IN THE UNLATCHED (DOWN) POSITION UNDER CERTAIN CONDITIONS BECAUSE THE BUCKLE ASSEMBLY CAN MOVE INSIDE THE SEAT BELT COVER. IF THE COVER MOVES FAR ENOUGH, IT CAN CREATE AN INTERFERENCE CONDITION WITH THE LATCH RELEASE BUTTON. WHEN IT DOES, THE SEAT BELT BUCKLE CANNOT BE LATCHED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES MANUFACTURED FROM AUGUST 1991 THROUGH JULY 1995. THE TRANSMISSION OIL COOLER LINE CAN SEPARATE WHEN THE VEHICLE IS OPERATED IN LOW TEMPERATURES IN COMBINATION WITH HIGH TRANSMISSION LOADS.

THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, "SEAT BELT ASSEMBLY ANCHORAGES."

THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, "SEAT BELT ASSEMBLY ANCHORAGES."

THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, "SEAT BELT ASSEMBLY ANCHORAGES."

THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, "SEAT BELT ASSEMBLY ANCHORAGES."

THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, "SEAT BELT ASSEMBLY ANCHORAGES."

THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, "SEAT BELT ASSEMBLY ANCHORAGES."

THESE VEHICLES WERE ASSEMBLED WITH A MALFUNCTION ALARM, LIGHTING AND LOCKING (MALL) MODULE THAT CAN CONTAIN A DAMAGED CAPACITOR. IF THE CAPACITOR IS DAMAGED, THE "KEY IN THE IGNITION" WARNING CHIME AND THE DRIVER SEAT BELT UNBUCKLED WARNING CHIME AND INDICATOR LAMP MAY NOT WORK. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 114, "THEFT PROTECTION" AND FMVSS NO. 208, "OCCUPANT CRASH PROTECTION." IN ADDITION, OTHER CHIME REMINDER FUNCTIONS, INTERIOR LIGHTING CONTROLS, AND POWER DOOR LOCKING FEATURES ARE ALSO AFFECTED.

THE FRONT OUTER SHOULDER BELT WEB SEW STOP CAN BECOME STUCK IN THE RETRACTOR. THE BELT CAN BE DIFFICULT TO PULL OUT OF THE RETRACTOR AND SOME OCCUPANTS MAY NOT BE ABLE TO FASTEN THE BELT.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

THE REAR WHEEL BRAKE HOSE(S) CAN CONTACT THE REAR SUSPENSION COMPONENTS CAUSING THE BRAKE HOSE(S) TO WEAR THROUGH.

THE REAR WHEEL BRAKE HOSE(S) CAN CONTACT THE REAR SUSPENSION COMPONENTS CAUSING THE BRAKE HOSE(S) TO WEAR THROUGH.

THE REAR WHEEL BRAKE HOSE(S) CAN CONTACT THE REAR SUSPENSION COMPONENTS CAUSING THE BRAKE HOSE(S) TO WEAR THROUGH.

IMPROPERLY MANUFACTURED BRAKE PEDAL ARM CAUSES THE BRAKE PEDAL ARM TO FRACTURE DURING BRAKING.

THE BRAKE LINES CAN CONTACT THE TRANSMISSION MOUNTING BRACKET OF THE FRAME SIDE RAIL. THE LINES CAN WEAR THROUGH RESULTING IN LOSS OF BRAKE FLUID, AND EVENTUAL LOSS OF HALF THE VEHICLE BRAKING SYSTEM.

THE BRAKE LINES CAN CONTACT THE TRANSMISSION MOUNTING BRACKET OF THE FRAME SIDE RAIL. THE LINES CAN WEAR THROUGH RESULTING IN LOSS OF BRAKE FLUID, AND EVENTUAL LOSS OF HALF THE VEHICLE BRAKING SYSTEM.

THE BRAKE LINES CAN CONTACT THE TRANSMISSION MOUNTING BRACKET OF THE FRAME SIDE RAIL. THE LINES CAN WEAR THROUGH RESULTING IN LOSS OF BRAKE FLUID, AND EVENTUAL LOSS OF HALF THE VEHICLE BRAKING SYSTEM.

THE RIGHT HAND SPINDLE NUT WAS NOT PROPERLY TIGHTENED DURING ASSEMBLY. THIS CAN CAUSE PREMATURE WHEEL BEARING FAILURE AND OVER TIME, THE SPINDLE CAN FRACTURE.

WATER INTRUSION CAN CAUSE A SHORT CIRCUIT IN THE POWER DOOR LOCK ASSEMBLY.

THESE VEHICLES WERE CONSTRUCTED WITH WELDS IN THE REAR COMPARTMENT PAN ASSEMBLY THAT ARE NOT SUFFICIENT TO COMPLY WITH THE REQUIREMENTS PERTAINING TO FUEL TANK LEAKAGE IN THE EVENT OF A REAR IMPACT COLLISION. THE FUEL TANK ASSEMBLIES DO NOT COMPLY WITH FMVSS NO. 301, "FUEL SYSTEM INTEGRITY."

THESE VEHICLES WERE SHIPPED WITH THE WRONG OWNER'S MANUAL, AND, THEREFORE, THE CORRECT INFORMATION REGARDING SAFETY BELT USAGE IS NOT AVAILABLE TO THE OWNER. THIS DOES NOT CONFORM WITH FMVSS NO. 209, "SEAT BELT ASSEMBLIES."

THE SECOND ROW, RIGHT HAND SHOULDER BELT CAN BECOME "PINCHED" BETWEEN THE SEAT AND THE DOOR FRAME PILLAR TRIM. THE SHOULDER BELT MAY NOT RETRACT PROPERLY, WHICH DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION." THE 1994 VEHICLES HAVE AN OPTIONAL INTEGRAL (BUILT IN) CHILDSEAT INSTALLED NEXT TO THE POWER SLIDING SIDE DOOR. THE 1993 INVOLVED VEHICLES HAVE STANDARD SEATS IN THAT SAME POSITION.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

VEHICLE FAILS TO CONFORM TO FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE SAFETY BELT OF THE LEFT THIRD ROW SEAT ON THE SIX PASSENGER VAN AND THE CENTER SECOND ROW SEAT OF THE SEVEN PASSENGER VAN MAY LOCK UP AND CANNOT BE WITHDRAWN FROM THE RETRACTOR.

THE THIRD ROW SAFETY BELT RETRACTORS MAY BE INSTALLED INCORRECTLY AND MAY LOCK-UP WHEN THE VEHICLE IS ON SLOPES OF LESS THAN 15 DEGREES, WHICH DOES NOT COMPLY WITH FMVSS NO. 209, "SEAT BELT ASSEMBLIES."

IN THE EVENT OF A PRIMARY ACCELERATOR CONTROL SPRING FAILURE, THE SECONDARY (BACK-UP) ACCELERATOR CONTROL RETURN SPRING WILL NOT RETURN THE THROTTLE TO THE FULLY CLOSED POSITION, AS REQUIRED BY FMVSS NO. 124, "ACCELERATOR CONTROL SYSTEM."

THE SAFETY BELT RETRACTORS FOR THE REAR CENTER POSITION ARE MISSING A PAWL SPRING AND IN CASE OF AN ACCIDENT, WILL ALLOW THE SAFETY BELT WEBBING TO EXTEND BEYOND THE MINIMUM REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

THE CRUISE CONTROL CABLE MAY SEPARATE FROM THE CONDUIT END FITTING WHILE ENGAGED AND ACCELERATOR CONTROL COULD BE LOST.

THE CRUISE CONTROL CABLE MAY SEPARATE FROM THE CONDUIT END FITTING WHILE ENGAGED AND ACCELERATOR CONTROL COULD BE LOST.

THE CRUISE CONTROL CABLE MAY SEPARATE FROM THE CONDUIT END FITTING WHILE ENGAGED AND ACCELERATOR CONTROL COULD BE LOST.

THE NEUTRAL START SAFETY SWITCH COULD HAVE BEEN FRACTURED DURING INSTALLATION.

THE BRAKE HOSES WERE MANUFACTURED INCORRECTLY, AND DO NOT COMPLY WITH FMVSS 106, "BRAKE HOSES."

THE BRAKE HOSES WERE MANUFACTURED INCORRECTLY, AND DO NOT COMPLY WITH FMVSS 106, "BRAKE HOSES."

THE BRAKE HOSES WERE MANUFACTURED INCORRECTLY, AND DO NOT COMPLY WITH FMVSS 106, "BRAKE HOSES."

THE DRIVER AND PASSENGER FRONT SEAT MANUAL RECLINING MECHANISMS DO NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 207, "SEATING SYSTEMS." THE SEAT BACK MECHANISMS WILL NOT LATCH UNDER CERTAIN CONDITIONS.

THE DRIVER AND PASSENGER FRONT SEAT MANUAL RECLINING MECHANISMS DO NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 207, "SEATING SYSTEMS." THE SEAT BACK MECHANISMS WILL NOT LATCH UNDER CERTAIN CONDITIONS.

THE DRIVER AND PASSENGER FRONT SEAT MANUAL RECLINING MECHANISMS DO NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 207, "SEATING SYSTEMS." THE SEAT BACK MECHANISMS WILL NOT LATCH UNDER CERTAIN CONDITIONS.

FRONT FUEL FEED HOSE ASSEMBLY COULD CRACK OR SEPARATE AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY, ALLOWING FUEL TO LEAK INTO THE ENGINE COMPARTMENT.

THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.

THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.

THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.

THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.

THE SHOULDER BELT GUIDE LOOP PLASTIC COVERING MAY CRACK AND EXPOSE THE STEEL SUB-PLATE.

THE GLOVE COMPARTMENT DOOR WILL NOT REMAIN CLOSED DURING CERTAIN LOAD FORCES ASSOCIATED WITH A VEHICLE CRASH. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 201.

THE OPTIONAL REMOTE ENTRY MODULE MAY HAVE A FAULT WHICH CAUSES RANDOM ACTUATION OF INTERIOR LAMPS, DOOR LOCKS, AND/OR TAILGATE RELEASE. THIS ACTUATION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED.

THE OPTIONAL REMOTE ENTRY MODULE MAY HAVE A FAULT WHICH CAUSES RANDOM ACTUATION OF INTERIOR LAMPS, DOOR LOCKS, AND/OR TAILGATE RELEASE. THIS ACTUATION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED.

THE OPTIONAL REMOTE ENTRY MODULE MAY HAVE A FAULT WHICH CAUSES RANDOM ACTUATION OF INTERIOR LAMPS, DOOR LOCKS, AND/OR TAILGATE RELEASE. THIS ACTUATION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED.

MOISTURE CAN ENTER THE EXPRESS-DOWN ELECTRONIC CONTROL MODULE AND CAUSE A SHORT CIRCUIT THAT CAUSES WINDOW OPERATION WITHOUT OPERATOR CONTROL, AND LEAVES THE WINDOW IN THE DOWN POSITION.

MOISTURE CAN ENTER THE EXPRESS-DOWN ELECTRONIC CONTROL MODULE AND CAUSE A SHORT CIRCUIT THAT CAUSES WINDOW OPERATION WITHOUT OPERATOR CONTROL, AND LEAVES THE WINDOW IN THE DOWN POSITION.

MOISTURE CAN ENTER THE EXPRESS-DOWN ELECTRONIC CONTROL MODULE AND CAUSE A SHORT CIRCUIT THAT CAUSES WINDOW OPERATION WITHOUT OPERATOR CONTROL, AND LEAVES THE WINDOW IN THE DOWN POSITION.

MOISTURE CAN ENTER THE EXPRESS-DOWN ELECTRONIC CONTROL MODULE AND CAUSE A SHORT CIRCUIT THAT CAUSES WINDOW OPERATION WITHOUT OPERATOR CONTROL, AND LEAVES THE WINDOW IN THE DOWN POSITION.

THE INTERMEDIATE SHAFT TO STEERING RACK LOWER COUPLING PINCH BOLT MAY BE MISSING.

THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.

THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.

THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.

THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.

A RIGHT HAND SEAT/SHOULDER BELT RETRACTOR MAY HAVE BEEN INSTALLED IN THE SECOND ROW LEFT HAND SEAT POSITION (DIRECTLY BEHIND DRIVER).

THE REVERSE SERVO APPLY PIN MAY BIND IN THE CASE WHICH COULD CAUSE REVERSE BAND DISTRESS (LOSS OR SLIPPING OF REVERSE), REVERSE BAND DRAG IN DRIVE RANGE (POOR PERFORMANCE -- POOR POWER), OR THE TRANSMISSION TO REMAIN IN REVERSE WHILE THE SHIFT INDICATOR SHOWS NEUTRAL GEAR POSITION.

THE REVERSE SERVO APPLY PIN MAY BIND IN THE CASE WHICH COULD CAUSE REVERSE BAND DISTRESS (LOSS OR SLIPPING OF REVERSE), REVERSE BAND DRAG IN DRIVE RANGE (POOR PERFORMANCE -- POOR POWER), OR THE TRANSMISSION TO REMAIN IN REVERSE WHILE THE SHIFT INDICATOR SHOWS NEUTRAL GEAR POSITION.

THE REVERSE SERVO APPLY PIN MAY BIND IN THE CASE WHICH COULD CAUSE REVERSE BAND DISTRESS (LOSS OR SLIPPING OF REVERSE), REVERSE BAND DRAG IN DRIVE RANGE (POOR PERFORMANCE -- POOR POWER), OR THE TRANSMISSION TO REMAIN IN REVERSE WHILE THE SHIFT INDICATOR SHOWS NEUTRAL GEAR POSITION.

SECONDARY HOOD LATCH ASSEMBLIES CAN CORRODE, CAUSING A HIGH LATCH RELEASE EFFORT AND POSSIBLY PREVENTING THE HOOD FROM LATCHING PROPERLY WHEN IT IS CLOSED.

VEHICLES HAVE BEEN SHIPPED WITH THE FUEL TANK SENDER SEAL OUT OF POSITION.

FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.

FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.

FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.

FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.

BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS WILL NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO IN VEHICLES EQUIPPED WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL.

BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS WILL NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO IN VEHICLES EQUIPPED WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL.

BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS WILL NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO IN VEHICLES EQUIPPED WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL.

BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS WILL NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO IN VEHICLES EQUIPPED WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL.

FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT FASTENER MAY PULL THROUGH DOOR MOUNTED ANCHOR PLATE.

FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT FASTENER MAY PULL THROUGH DOOR MOUNTED ANCHOR PLATE.

FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT FASTENER MAY PULL THROUGH DOOR MOUNTED ANCHOR PLATE.

FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT FASTENER MAY PULL THROUGH DOOR MOUNTED ANCHOR PLATE.

FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT FASTENER MAY PULL THROUGH DOOR MOUNTED ANCHOR PLATE.

IMPROPERLY TORQUED CONNECTIONS OF FRONT FUEL FEED AND RETURN HOSES TO FUEL PIPES AT THE BODY RAIL COULD LOOSEN AND LEAK FUEL INTO THE UNDERHOOD AREA.

FRONT FUEL FEED HOSE ASSEMBLY COULD CRACK OR SEPARATE AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY, ALLOWING FUEL TO LEAK INTO THE ENGINE COMPARTMENT.

THE REAR MODULAR SEAT FRAME HOLD-DOWN HOOKS MAY NOT MEET THE REQUIRED PULL FORCE AT THE REAR SET ANCHORAGE.

THE ELECTRONIC AIR CONDITIONING CONTROL MAY NOT FUNCTION WHEN STARTING CAR THAT HAS BEEN PARKED FOR A FEW HOURS WITH IGNITION OFF.

THE ELECTRONIC AIR CONDITIONING CONTROL MAY NOT FUNCTION WHEN STARTING CAR THAT HAS BEEN PARKED FOR A FEW HOURS WITH IGNITION OFF.

THE ELECTRONIC AIR CONDITIONING CONTROL MAY NOT FUNCTION WHEN STARTING CAR THAT HAS BEEN PARKED FOR A FEW HOURS WITH IGNITION OFF.

THE ELECTRONIC AIR CONDITIONING CONTROL MAY NOT FUNCTION WHEN STARTING CAR THAT HAS BEEN PARKED FOR A FEW HOURS WITH IGNITION OFF.

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

LEFT FRONT BRAKE PIPE MAY CONTACT THE CRUISE CONTROL SERVO BRACKET.

ONE OR BOTH ABS HYDRAULIC UNIT MOUNTING BOLTS MAY NOT BE PROPERLY SEATED AND COULD LOOSEN.

FUEL FEED HOSE COULD LEAK AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY.

THE PARKING BRAKE CABLE MAY BE DISCONNECTED FROM THE LEFT REAR BRAKE CALIPER.

THE PARKING BRAKE CABLE MAY BE DISCONNECTED FROM THE LEFT REAR BRAKE CALIPER.

THE PARKING BRAKE CABLE MAY BE DISCONNECTED FROM THE LEFT REAR BRAKE CALIPER.

THE PARKING BRAKE CABLE MAY BE DISCONNECTED FROM THE LEFT REAR BRAKE CALIPER.

THE PARKING BRAKE CABLE MAY BE DISCONNECTED FROM THE LEFT REAR BRAKE CALIPER.

INSUFFICIENT CLEARANCE BETWEEN THE POWER STEERING PUMP PRESSURE HOSE ASSEMBLY AND THE TRANSMISSION GOVERNOR/SPEED SENSOR CONNECTOR COULD CAUSE ABRASION OF THE HOSE.

EXCESSIVE ACCELERATOR CABLE FRICTION MAY RESTRICT THE CABLES FREE MOVEMENT BETWEEN THE ACCELERATOR PEDAL AND THE THROTTLE BODY.

THE FUEL FEED OR FUEL RETURN HOSE AT THE ENGINE MAY RUB AGAINST A SHIFT LEVER ON THE 5 SPEED TRANSAXLE.

THE FUEL FEED AND/OR RETURN HOSE/PIPE ASSEMBLIES COULD CRACK OR SEPARATE, ALLOWING FUEL TO LEAK INTO THE UNDERHOOD AREA.

THE FUEL FEED AND/OR RETURN HOSE/PIPE ASSEMBLIES COULD CRACK OR SEPARATE, ALLOWING FUEL TO LEAK INTO THE UNDERHOOD AREA.

MANUAL VALVE LINK IN THE TRANSMISSION MAY HAVE BEEN IMPROPERLY FORMED.

MANUAL VALVE LINK IN THE TRANSMISSION MAY HAVE BEEN IMPROPERLY FORMED.

MANUAL VALVE LINK IN THE TRANSMISSION MAY HAVE BEEN IMPROPERLY FORMED.

MANUAL VALVE LINK IN THE TRANSMISSION MAY HAVE BEEN IMPROPERLY FORMED.

AN IN LINE FUSIBLE LINK MAY MELT DOWN AND CAUSE A FIRE.

SMALL CRACKS MAY DEVELOP IN THE BODY PILLAR AROUND THE DOOR STRIKER BOLT HOLE.

THE METAL FLOOR PAN ANCHOR BAR COULD FATIGUE AND BREAK AROUND THE LEFT FRONT OUTER SEAT ADJUSTER STUD OF THE DRIVERS SEAT, ALLOWING THE STUD TO SEPARATE FROM THE FLOOR PAN ANCHOR BAR.

THE METAL FLOOR PAN ANCHOR BAR COULD FATIGUE AND BREAK AROUND THE LEFT FRONT OUTER SEAT ADJUSTER STUD OF THE DRIVERS SEAT, ALLOWING THE STUD TO SEPARATE FROM THE FLOOR PAN ANCHOR BAR.

POOR BOND ADHESION BETWEEN THE WINDSHIELD GLASS AND MOUNTING COULD ALLOW THE WINDSHIELD TO SEPARATE DURING A 30 MPH FRONTAL BARRIER TEST REQUIRED BY FMVSS 212.

CONSOLE FRONT COMPARTMENT DOOR MAY NOT REMAIN CLOSED DURING LOAD FORCES THAT MAY BE EXPERIENCED IN A CRASH AS REQUIRED BY FMVSS 201.

LEFT HANDED DRIVER'S SIDE SHOULDER BELT ANCHOR PLATE MAY BE UPSIDE DOWN IN LOCK PILLAR SO THAT THE UNTHREADED SLOT OF THE PLATE ALIGNED WITH THE HOLE IN THE LOCK PILLAR. THIS RESULTED IN THE ANCHOR BOLT BEING DRIVEN INTO THE SLOT INSTEAD OF THE THREADED HOLE OF THE ANCHOR PLATE. CONSEQUENCE OF DEFECT: IN A VEHICLE CRASH, BELT ANCHOR BOLT MAY PULL LOOSE FROM ANCHOR PLATE, THUS FAILING TO COMPLY WITH FMVSS 210, SEAT BELT ASSEMBLY ANCHORAGES, AND INCREASES LIKELIHOOD OF INJURY TO OCCUPANT.

LEFT HANDED DRIVER'S SIDE SHOULDER BELT ANCHOR PLATE MAY BE UPSIDE DOWN IN LOCK PILLAR SO THAT THE UNTHREADED SLOT OF THE PLATE ALIGNED WITH THE HOLE IN THE LOCK PILLAR. THIS RESULTED IN THE ANCHOR BOLT BEING DRIVEN INTO THE SLOT INSTEAD OF THE THREADED HOLE OF THE ANCHOR PLATE. CONSEQUENCE OF DEFECT: IN A VEHICLE CRASH, BELT ANCHOR BOLT MAY PULL LOOSE FROM ANCHOR PLATE, THUS FAILING TO COMPLY WITH FMVSS 210, SEAT BELT ASSEMBLY ANCHORAGES, AND INCREASES LIKELIHOOD OF INJURY TO OCCUPANT.

LEFT HANDED DRIVER'S SIDE SHOULDER BELT ANCHOR PLATE MAY BE UPSIDE DOWN IN LOCK PILLAR SO THAT THE UNTHREADED SLOT OF THE PLATE ALIGNED WITH THE HOLE IN THE LOCK PILLAR. THIS RESULTED IN THE ANCHOR BOLT BEING DRIVEN INTO THE SLOT INSTEAD OF THE THREADED HOLE OF THE ANCHOR PLATE. CONSEQUENCE OF DEFECT: IN A VEHICLE CRASH, BELT ANCHOR BOLT MAY PULL LOOSE FROM ANCHOR PLATE, THUS FAILING TO COMPLY WITH FMVSS 210, SEAT BELT ASSEMBLY ANCHORAGES, AND INCREASES LIKELIHOOD OF INJURY TO OCCUPANT.

THE LEFT AND RIGHT REAR LOWER CONTROL ARM BALL JOINT STUD TO KNUCKLE ATTACHMENT MAY HAVE BEEN INADEQUATELY TIGHTENED. CONSEQUENCE OF DEFECT: THIS COULD ALLOW THE REAR LOWER CONTROL ARM BALL JOINT STUD TO LOOSEN AT THE KNUCKLE ATTACHMENT. A LOOSE BALL JOINT STUD COULD EVENTUALLY BREAK AND SEPARATE FROM THE KNUCKLE. SEPARATION COULD CAUSE A LOSS OF VEHICLE CONTROL WHICH COULD RESULT IN A VEHICLE CRASH WITHOUT PRIOR WARNING.

PARKING BRAKE LEVER MECHANISMS MAY NOT PROPERLY ENGAGE WHEN APPLIED AS REQUIRED BY FMVSS 105. CONSEQUENCE OF DEFECT: VEHICLE COULD UNEXPECTEDLY ROLL AWAY UNCONTROLLED, WHICH COULD RESULT IN A VEHICLE CRASH.

PARKING BRAKE LEVER MECHANISMS MAY NOT PROPERLY ENGAGE WHEN APPLIED AS REQUIRED BY FMVSS 105. CONSEQUENCE OF DEFECT: VEHICLE COULD UNEXPECTEDLY ROLL AWAY UNCONTROLLED, WHICH COULD RESULT IN A VEHICLE CRASH.

THE SECONDARY HOOD LATCH MAY BE INCORRECTLY ALIGNED, OR MAY EXHIBIT A BINDING CONDITION OF THE LATCH PIVOT. CONSEQUENCE OF DEFECT: THIS CONDITION COULD RESULT IN THE PRIMARY HOOD LATCH NOT BEING COMPLETELY ENGAGED TO THE HOOD, THE HOOD COULD UNEXPECTEDLY OPEN WHILE VEHICLE IS IN MOTION. SHOULD THIS OCCUR, THE HOOD MAY CONTACT THE WINDSHIELD REDUCING THE FORWARD VISION AREA OF THE DRIVER AND A VEHICLE CRASH WITHOUT PRIOR WARNING COULD OCCUR.

THE ENGINE AIR CLEANER PLASTIC TRIM COVER COULD FALL OFF THE AIR CLEANER ASSEMBLY AND LAND ON THE EXHAUST MANIFOLD CREATING A FIRE HAZARD. CONSEQUENCE OF DEFECT: IF THE CAR IS BEING OPERATED AT THE TIME THAT THE PLASTIC TRIM COVER FALLS OFF, AN ENGINE COMPARTMENT FIRE COULD OCCUR WITHOUT WARNING.

THE ENGINE AIR CLEANER PLASTIC TRIM COVER COULD FALL OFF THE AIR CLEANER ASSEMBLY AND LAND ON THE EXHAUST MANIFOLD CREATING A FIRE HAZARD. CONSEQUENCE OF DEFECT: IF THE CAR IS BEING OPERATED AT THE TIME THAT THE PLASTIC TRIM COVER FALLS OFF, AN ENGINE COMPARTMENT FIRE COULD OCCUR WITHOUT WARNING.

THE RIGHT REAR TAIL LAMP ASSEMBLY MAY BE INCORRECTLY ASSEMBLED. THE MISASSEMBLED UNITS WILL RESULT IN REDUCED ILLUMINATION WHICH WILL CAUSE THE LAMP ASSEMBLY TO BE IN NON-COMPLIANCE WITH FMVSS 108 LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. CONSEQUENCE OF DEFECT: REDUCED ILLUMINATION WHICH DOES NOT MEET THE FEDERAL STANDARD MAY NOT BE SUFFICIENT TO BE NOTICED ON THE HIGHWAY, THEREFORE MAY CONTRIBUTE TO AN ACCIDENT.

THE RIGHT REAR TAIL LAMP ASSEMBLY MAY BE INCORRECTLY ASSEMBLED. THE MISASSEMBLED UNITS WILL RESULT IN REDUCED ILLUMINATION WHICH WILL CAUSE THE LAMP ASSEMBLY TO BE IN NON-COMPLIANCE WITH FMVSS 108 LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. CONSEQUENCE OF DEFECT: REDUCED ILLUMINATION WHICH DOES NOT MEET THE FEDERAL STANDARD MAY NOT BE SUFFICIENT TO BE NOTICED ON THE HIGHWAY, THEREFORE MAY CONTRIBUTE TO AN ACCIDENT.

AN INCORRECTLY INDEXED WIRING HARNESS MAY CAUSE THE CENTER HIGH MOUNTED STOP LAMP TO REMAIN ILLUMINATED WHEN THE HEADLIGHTS OR PARKING LAMPS ARE ON. FMVSS 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT REQUIRES THAT THIS STOP LAMP BE LIGHTED ONLY WHEN THE BRAKES ARE APPLIED. ALSO, THE OPERA LAMPS MAY COME ON WHEN THE BRAKES ARE APPLIED. CONSEQUENCE OF DEFECT: THE CENTER HIGH MOUNTED STOP LAMP PROVIDES ADDITIONAL WARNING THAT THE VEHICLE IS SLOWING OR STOPPING. IF THIS LAMP MALFUNCTIONS, IT MAY CONTRIBUTE TO A REAR END ACCIDENT.

AN INCORRECTLY INDEXED WIRING HARNESS MAY CAUSE THE CENTER HIGH MOUNTED STOP LAMP TO REMAIN ILLUMINATED WHEN THE HEADLIGHTS OR PARKING LAMPS ARE ON. FMVSS 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT REQUIRES THAT THIS STOP LAMP BE LIGHTED ONLY WHEN THE BRAKES ARE APPLIED. ALSO, THE OPERA LAMPS MAY COME ON WHEN THE BRAKES ARE APPLIED. CONSEQUENCE OF DEFECT: THE CENTER HIGH MOUNTED STOP LAMP PROVIDES ADDITIONAL WARNING THAT THE VEHICLE IS SLOWING OR STOPPING. IF THIS LAMP MALFUNCTIONS, IT MAY CONTRIBUTE TO A REAR END ACCIDENT.

AN INCORRECTLY INDEXED WIRING HARNESS MAY CAUSE THE CENTER HIGH MOUNTED STOP LAMP TO REMAIN ILLUMINATED WHEN THE HEADLIGHTS OR PARKING LAMPS ARE ON. FMVSS 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT REQUIRES THAT THIS STOP LAMP BE LIGHTED ONLY WHEN THE BRAKES ARE APPLIED. ALSO, THE OPERA LAMPS MAY COME ON WHEN THE BRAKES ARE APPLIED. CONSEQUENCE OF DEFECT: THE CENTER HIGH MOUNTED STOP LAMP PROVIDES ADDITIONAL WARNING THAT THE VEHICLE IS SLOWING OR STOPPING. IF THIS LAMP MALFUNCTIONS, IT MAY CONTRIBUTE TO A REAR END ACCIDENT.

THE THROTTLE RETURN SPRING ASSEMBLY MAY FAIL PREVENTING THE THROTTLE FROM RETURNING TO THE CLOSED (IDLE) POSITION WHEN THE ACCELERATOR PEDAL IS RELEASED. CONSEQUENCE OF DEFECT: ENGINE SPEED MAY NOT DECREASE AND LOSS OF ACCELERATOR CONTROL COULD RESULT IN AN ACCIDENT WITHOUT PRIOR WARNING.

A LOSS OF BONDING ADHESION BETWEEN THE PAINT AND THE WINDSHIELD OPENING AREA COULD ALLOW THE WINDSHIELD TO SEPARATE DURING A 30 MILE PER HOUR FRONTAL BARRIER TEST REQUIRED BY FMVSS 212, WINDSHIELD RETENTION. CONSEQUENCE OF DEFECT: WINDSHIELD SEPARATION DURING AN ACCIDENT COULD RESULT IN AN UNBELTED OCCUPANT BEING EJECTED FROM THE CAR AND SEVERLY INJURED.

THE TIRE PLACARD LABEL ON THE LEFT FRONT DOOR MAY HAVE BEEN PRINTED WITH AN ERROR WHICH SPECIFIES A HIGHER MAXIMUM LOADING THAN IS ALLOWED. CONSEQUENCE OF DEFECT: EXCESSIVE VEHICLE LOADING COULD CAUSE A TIRE BLOWOUT AND RESULT IN AN ACCIDENT.

THE REAR AXLE CONTROL ARM LOCATES AND HELPS CONTROL AXLE MOVEMENT; IT ATTACHES TO THE FRAME WITH A BRACKET. THE REAR CONTROL ARM BRACKET ATTACHING BOLTS USED ON SOME OF THE INVOLVED VEHICLES MAY FRACTURE. FRACTURE OF ALL FOUR BOLTS ON ONE SIDE OF THE VEHICLE CAN RESULT IN THE CONTROL ARM DROPPING ENOUGH TO CUT THE REAR BRAKE HOSE. A SEVERED BRAKE HOSE WOULD RESULT IN BRAKE FLUID LOSS AND PARTIAL LOSS OF BRAKING ABILITY.

THE VEHICLES WERE ASSEMBLED WITH FRONT SEAT BELT RETRACTORS WHICH MAY NOT PERFORM ADEQUATELY DURING A COLLISION.

THE VEHICLES WERE ASSEMBLED WITH FRONT SEAT BELT RETRACTORS WHICH MAY NOT PERFORM ADEQUATELY DURING A COLLISION.

THE VEHICLES WERE ASSEMBLED WITH FRONT SEAT BELT RETRACTORS WHICH MAY NOT PERFORM ADEQUATELY DURING A COLLISION.

THE TIE RODS ARE PART OF THE STEERING LINKAGE AND TRANSMIT TURNING MOVEMENTS TO THE WHEELS. THE BOLTS THAT FASTEN THE TIE RODS TO THEIR ADJUSTERS MAY NOT BE TIGHT ENOUGH. THIS COULD ALLOW THE TIE ROD TO LOOSEN AND DETACH ITSELF FROM THE ADJUSTER.

THE TIE RODS ARE PART OF THE STEERING LINKAGE AND TRANSMIT TURNING MOVEMENTS TO THE WHEELS. THE BOLTS THAT FASTEN THE TIE RODS TO THEIR ADJUSTERS MAY NOT BE TIGHT ENOUGH. THIS COULD ALLOW THE TIE ROD TO LOOSEN AND DETACH ITSELF FROM THE ADJUSTER.

THE TIE RODS ARE PART OF THE STEERING LINKAGE AND TRANSMIT TURNING MOVEMENTS TO THE WHEELS. THE BOLTS THAT FASTEN THE TIE RODS TO THEIR ADJUSTERS MAY NOT BE TIGHT ENOUGH. THIS COULD ALLOW THE TIE ROD TO LOOSEN AND DETACH ITSELF FROM THE ADJUSTER.

VEHICLES WERE ASSEMBLED WITH AN INCORRECT BRAKE PEDAL BRACKET WHICH CAUSES THE BRAKE PEDAL TO BE LOCATED IN A POSITION LOWER THAN NORMAL.

SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.

SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.

SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.

SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.

SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.

SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.

THE THROTTLE MAY JAM AND MAY NOT RETURN TO THE CLOSED POSITION. THIS PROBLEM IS DUE TO THE OMISSION, DURING ASSEMBLY, OF A NUT ON THE CRUISE CONTROL ROD WHICH LIMITS TRAVEL IN THE THROTTLE MECHANISM.

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH FRONT BUCKET SEATS. THE FRONT SEAT RECLINER MECHANISM LOWER BOLTS CAN LOOSEN. A LOOSE BOLT COULD FATIGUE AND BREAK, RESULTING IN THE SEAT BACK FALLING REARWARD.

THE FUEL SYSTEM MAY LEAK AT THE THROTTLE BODY INJECTION FUEL FEED PIPE CONNECTION. CONSEQUENCE OF DEFECT: THIS LEAKAGE COULD RESULT IN AN UNDERHOOD FIRE WHICH COULD SPREAD TO THE PASSENGER COMPARTMENT AND CAUSE BURN INJURIES TO OCCUPANTS.

THE FUEL SYSTEM MAY LEAK AT THE THROTTLE BODY INJECTION FUEL FEED PIPE CONNECTION. CONSEQUENCE OF DEFECT: THIS LEAKAGE COULD RESULT IN AN UNDERHOOD FIRE WHICH COULD SPREAD TO THE PASSENGER COMPARTMENT AND CAUSE BURN INJURIES TO OCCUPANTS.