Plymouth Recall History

FEDERAL-MOGUL IS RECALLING CERTAIN REPLACEMENT CONTROL ARM ASSEMBLIES, PART NUMBERS K7425, 10945, FA4510X, K7427, 10946, AND FA4611X, SOLD FOR USE ON VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE BALL JOINT ON THE CONTROL ARM ASSEMBLY CAN FAIL CAUSING THE BALL STUD TO WEAR THROUGH THE CONTROL ARM HOUSING RESULTING IN NOISE AND/OR SEPARATION OF THE BALL STUD FROM THE HOUSING.

CURT MFG IS RECALLING CERTAIN CLASS 3 RECEIVER HITCHES, P/N 13347, SOLD AS AFTERMARKET EQUIPMENT FOR USE ON 1997-2007 CHRYSLER TOWN AND COUNTRY VANS, 1996-2007 DODGE CARAVANS, AND 1996-2004 PLYMOUTH VOYAGER VANS. WHEN THE HITCH IS LOADED TO THE MAXIMUM RATING, THE HITCH MAY FRACTURE OR BREAK AT THE BEND LOCATION WHERE THE MAIN BODY OF THE HITCH MEETS THE HITCH MUFFLER STRAP.

CURT MFG IS RECALLING CERTAIN CLASS 3 RECEIVER HITCHES, P/N 13347, SOLD AS AFTERMARKET EQUIPMENT FOR USE ON 1997-2007 CHRYSLER TOWN AND COUNTRY VANS, 1996-2007 DODGE CARAVANS, AND 1996-2004 PLYMOUTH VOYAGER VANS. WHEN THE HITCH IS LOADED TO THE MAXIMUM RATING, THE HITCH MAY FRACTURE OR BREAK AT THE BEND LOCATION WHERE THE MAIN BODY OF THE HITCH MEETS THE HITCH MUFFLER STRAP.

QUALIS AUTOMOTIVE IS RECALLING CERTAIN AFTERMARKET BALL JOINTS SOLD FOR USE ON CERTAIN PASSENGER VEHICLES. THE SOCKET MAY HAVE BEEN EXCESSIVELY HARDENED WHICH COULD CAUSE IT TO CRACK NEAR THE RETAINING RING GROOVE ALLOWING THE BALL STUD TO SEPARATE UNDER IMPACT LOAD. THE SUBJECT BALL JOINTS WERE SOLD AS FOUR PART NUMBERS, D10945, D10946, G10945, AND G10946. THE AFFECTED CONTROL ARMS, D10945 AND D10946, ARE STAMPED WITH THE FOLLOWING DATES ON THE BALL JOINTS: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, AND 116609. THE G10945 AND G10946 ARE THE SAME PART AS THE D10945 AND D10946 RESPECTIVELY. THEY ARE LABELED DIFFERENTLY DEPENDING ON THE AFTERMARKET CUSTOMER.

IMPORT PRODUCTS IS RECALLING 30,351 FUEL FILTERS SOLD TO AND BRANDED BY THE AFFINIA GROUP AS CARQUEST P/N 86523, NAPA P/N 3523, AND WIX P/N 33523 FOR USE AS REPLACEMENT EQUIPMENT ON THE VEHICLES LISTED ABOVE. THESE FILTERS MAY DEVELOP A LEAK IN THE HOSE ASSEMBLY AND/OR CONNECTORS DUE TO IMPROPERLY ADHERED LINE CONNECTORS.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

CERTAIN CURVED TEMPERED REPLACEMENT GLASS MANUFACTURED BY HANGZHOU SAFETY GLASS LTD AND SUPPLIED TO SAFELITE BY AUTO TEMP INC., IDENTIFIED AS DOT-430, AND SOLD FOR USE ON CERTAIN DOMESTIC AND FOREIGN VEHICLES MAY NOT BREAK INTO SMALL PIECES AS EXPECTED OF TEMPERED GLASS AND FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 205, "GLAZING MATERIALS."

CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

CERTAIN AIRTEX FUEL PUMP MODULES, P/NOS. E7089M, E7094M, E7113M, AND E7129M, MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006. THESE FUEL PUMP MODULES WERE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

CERTAIN AIRTEX FUEL PUMP MODULES, P/NOS. E7089M, E7094M, E7113M, AND E7129M, MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006. THESE FUEL PUMP MODULES WERE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH 2.4 LITER ENGINES, THE HIGH PRESSURE POWER STEERING HOSE MAY PREMATURELY HEAT AGE AND DEVELOP A LEAK.

CERTAIN AFTERMARKET BRAKE HYDRAULIC MASTER CYLINDERS SOLD AS REPLACEMENT BRAKE CYLINDERS FOR CERTAIN FORD, DAIMLERCHRYSLER, AND JEEP PASSENGER VEHICLES. THESE BRAKE CYLINDERS WERE SOLD UNDER THE BRAND NAMES OF NAPA, RAYBESTOS, AIMCO, AC DELCO, CARQUEST, BENDIX, AND WAGNER. ONLY PRODUCTS THAT WERE MANUFACTURED FROM JULY 27, 2005 THROUGH JANUARY 17, 2006 (DATE CODES 0529 THROUGH 0602) ARE SUBJECT TO THIS RECALL. WHEN SUBJECT TO VERY COLD TEMPERATURES, AN INTERNAL SEAL IN THE MASTER CYLINDER COULD LOSE FLEXIBILITY AND MAY CAUSE BRAKE FLUID TO LEAK.

CERTAIN AFTERMARKET BRAKE HYDRAULIC MASTER CYLINDERS SOLD AS REPLACEMENT BRAKE CYLINDERS FOR CERTAIN FORD, DAIMLERCHRYSLER, AND JEEP PASSENGER VEHICLES. THESE BRAKE CYLINDERS WERE SOLD UNDER THE BRAND NAMES OF NAPA, RAYBESTOS, AIMCO, AC DELCO, CARQUEST, BENDIX, AND WAGNER. ONLY PRODUCTS THAT WERE MANUFACTURED FROM JULY 27, 2005 THROUGH JANUARY 17, 2006 (DATE CODES 0529 THROUGH 0602) ARE SUBJECT TO THIS RECALL. WHEN SUBJECT TO VERY COLD TEMPERATURES, AN INTERNAL SEAL IN THE MASTER CYLINDER COULD LOSE FLEXIBILITY AND MAY CAUSE BRAKE FLUID TO LEAK.

CERTAIN AFTERMARKET BRAKE HYDRAULIC MASTER CYLINDERS SOLD AS REPLACEMENT BRAKE CYLINDERS FOR CERTAIN FORD, DAIMLERCHRYSLER, AND JEEP PASSENGER VEHICLES. THESE BRAKE CYLINDERS WERE SOLD UNDER THE BRAND NAMES OF NAPA, RAYBESTOS, AIMCO, AC DELCO, CARQUEST, BENDIX, AND WAGNER. ONLY PRODUCTS THAT WERE MANUFACTURED FROM JULY 27, 2005 THROUGH JANUARY 17, 2006 (DATE CODES 0529 THROUGH 0602) ARE SUBJECT TO THIS RECALL. WHEN SUBJECT TO VERY COLD TEMPERATURES, AN INTERNAL SEAL IN THE MASTER CYLINDER COULD LOSE FLEXIBILITY AND MAY CAUSE BRAKE FLUID TO LEAK.

ON CERTAIN MINIVANS, THE DRIVER'S AIR BAG MAY BECOME DISABLED DUE TO A FAILURE OF THE CLOCKSPRING, WHICH IS LOCATED IN THE HUB OF THE STEERING WHEEL.

ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.

ON CERTAIN PASSENGER VEHICLES, THE LOWER CONTROL ARM BALL JOINTS MAY EXPERIENCE A LOSS OF LUBRICATION THAT CAN RESULT IN ACCELERATED WEAR AND POSSIBLE SEPARATION FROM THE STEERING KNUCKLE.

ON CERTAIN MINI VANS, THE CLOCKSPRING ASSEMBLY MAY HAVE BEEN WOUND INCORRECTLY DURING THE VEHICLE ASSEMBLY PROCESS.

ON CERTAIN MINI VANS, THE CLOCKSPRING ASSEMBLY MAY HAVE BEEN WOUND INCORRECTLY DURING THE VEHICLE ASSEMBLY PROCESS.

ON CERTAIN MINIVANS, SOME TRIM MATERIAL CAN LOOSEN AND DROP INTO THE REAR OUTBOARD SEAT BELT ASSEMBLY, CAUSING THE SEAT BELT TO BECOME INOPERATIVE.

VEHICLE DESCRIPTION: MINI VANS BUILT WITH 3.3L AND 3.8L ENGINES HAVE FUEL RAILS WITH NITROLE RUBBER O-RING SEALS THAT CAN DEGRADE OVER TIME. FUEL LEAKAGE FROM THE UNDERHOOD FUEL INJECTION FUEL RAIL COULD RESULT, INCREASING THE LIKELIHOOD OF A VEHICLE FIRE.

VEHICLE DESCRIPTION: MINI VANS BUILT WITH 3.3L AND 3.8L ENGINES HAVE FUEL RAILS WITH NITROLE RUBBER O-RING SEALS THAT CAN DEGRADE OVER TIME. FUEL LEAKAGE FROM THE UNDERHOOD FUEL INJECTION FUEL RAIL COULD RESULT, INCREASING THE LIKELIHOOD OF A VEHICLE FIRE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IN THE PRESENCE OF OIL AND HEAT, THE BRAKE BOOSTER VACUUM HOSE COULD SWELL AND LOOSEN FROM THE INTAKE MANIFOLD.

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES, PICKUP TRUCKS AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." SOME OF THE OWNER'S MANUALS FOR THESE VEHICLES ARE MISSING INSTRUCTIONS THAT PROVIDE A STEP-BY-STEP PROCEDURE, INCLUDING DIAGRAMS, FOR PROPERLY ATTACHING A CHILD RESTRAINT SYSTEM'S TETHER STRAP TO THE TETHER ANCHORAGE.

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES, PICKUP TRUCKS AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." SOME OF THE OWNER'S MANUALS FOR THESE VEHICLES ARE MISSING INSTRUCTIONS THAT PROVIDE A STEP-BY-STEP PROCEDURE, INCLUDING DIAGRAMS, FOR PROPERLY ATTACHING A CHILD RESTRAINT SYSTEM'S TETHER STRAP TO THE TETHER ANCHORAGE.

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES, PICKUP TRUCKS AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." SOME OF THE OWNER'S MANUALS FOR THESE VEHICLES ARE MISSING INSTRUCTIONS THAT PROVIDE A STEP-BY-STEP PROCEDURE, INCLUDING DIAGRAMS, FOR PROPERLY ATTACHING A CHILD RESTRAINT SYSTEM'S TETHER STRAP TO THE TETHER ANCHORAGE.

VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH 2-SPOKE LUXURY WHEELS MANUFACTURED JULY 1992 THROUGH JUNE 1993; OR EQUIPPED WITH 4-SPOKE SPORT WHEELS MANUFACTURED FROM JULY 1992 THROUGH SEPTEMBER 1993. THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN.

VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH 2-SPOKE LUXURY WHEELS MANUFACTURED JULY 1992 THROUGH JUNE 1993; OR EQUIPPED WITH 4-SPOKE SPORT WHEELS MANUFACTURED FROM JULY 1992 THROUGH SEPTEMBER 1993. THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. SOME OF THESE VEHICLES MAY HAVE BEEN BUILT WITH AN INADEQUATE WELD BETWEEN THE RIGHT FRONT BRAKE HOSE BLOCK AND THE STAND-OFF BRACKET.

VEHICLE DESCRIPTION: PASSENGER CARS. VAPORS FROM THE POSITIVE CRANKCASE VENTILATION (PCV) SYSTEM CAN CONDENSE AND FREEZE INSIDE OF THE THROTTLE BODY WHEN THE VEHICLE IS OPERATED IN EXTREMELY COLD AMBIENT TEMPERATURES.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AFFECTED VEHICLES WERE BUILT WITH INCORRECT CHILD LOCK INSTRUCTION LABELS.

VEHICLE DESCRIPTION: MINIVANS. THE LEFT HAND WINDSHIELD WIPER PIVOT DRIVE ARM WAS NOT MECHANICALLY STAKED TO THE PIVOT SHAFT.

VEHICLE DESCRIPTION: MINIVANS. THE LEFT HAND WINDSHIELD WIPER PIVOT DRIVE ARM WAS NOT MECHANICALLY STAKED TO THE PIVOT SHAFT.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AFFECTED VEHICLES WERE BUILT WITH UNPAINTED FUEL TANK STRAPS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. SOME ALUMINUM CASTINGS USED IN THE MANUFACTURE OF THE VEHICLE FRAME MAY HAVE MISSED THE REQUIRED HEAT TREATMENT OPERATION RESULTING IN SOFT FRAME CASTINGS.

VEHICLE DESCRIPTION: MINIVANS. FUEL CAN LEAK FROM THE FUEL TANK AT THE INTERFACE OF THE FUEL PUMP MODULE ATTACHMENT.

VEHICLE DESCRIPTION: MINIVANS. FUEL CAN LEAK FROM THE FUEL TANK AT THE INTERFACE OF THE FUEL PUMP MODULE ATTACHMENT.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE RIGHT REAR BRAKE TUBE CAN CONTACT THE EXHAUST SYSTEM CLAMP AND WEAR A HOLE IN IT.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE BRAKE SYSTEM ON THESE VEHICLES DOES NOT COMPLY WITH FMVSS NO. 105, "HYDRAULIC BRAKE SYSTEMS."

VEHICLE DESCRIPTION: MINI VANS. THE BOLTS USED TO ATTACH THE STRUT TO THE BODY AND THE REAR LIFTGATE CAN ACCUMULATE FATIGUE DAMAGE IF THREE FACTORS COMBINE. IF THE BOLT IS LOOSE, THE GAS STRUT IS OVER-PRESSURIZED, AND THE FREQUENCY OF OPENING AND CLOSING CYCLES IS HIGHER THAN FOR THE AVERAGE CUSTOMER, THE BOLT CAN FAIL.

VEHICLE DESCRIPTION: MINI VANS. THE BOLTS USED TO ATTACH THE STRUT TO THE BODY AND THE REAR LIFTGATE CAN ACCUMULATE FATIGUE DAMAGE IF THREE FACTORS COMBINE. IF THE BOLT IS LOOSE, THE GAS STRUT IS OVER-PRESSURIZED, AND THE FREQUENCY OF OPENING AND CLOSING CYCLES IS HIGHER THAN FOR THE AVERAGE CUSTOMER, THE BOLT CAN FAIL.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER SEAT BACK ATTACHING BOLT ON THE DRIVER SEAT CAN FAIL AND SEPARATE.

VEHICLE DESCRIPTION: MINI VANS. THE WIRING THAT INITIATES THE DRIVER AND/OR PASSENGER AIR BAG COULD ELECTRICALLY SHORT CIRCUIT TO GROUND. A SHORT CIRCUIT TO GROUND THAT EXISTS IMMEDIATELY AFTER TURNING THE IGNITION KEY TO THE "ON" OR "START" POSITION CAN CAUSE THE AIR BAG(S) TO INADVERTENTLY DEPLOY.

VEHICLE DESCRIPTION: MINI VANS. THE WIRING THAT INITIATES THE DRIVER AND/OR PASSENGER AIR BAG COULD ELECTRICALLY SHORT CIRCUIT TO GROUND. A SHORT CIRCUIT TO GROUND THAT EXISTS IMMEDIATELY AFTER TURNING THE IGNITION KEY TO THE "ON" OR "START" POSITION CAN CAUSE THE AIR BAG(S) TO INADVERTENTLY DEPLOY.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE FRONT SUSPENSION LOWER CONTROL ARMS MAY HAVE BEEN INADEQUATELY WELDED BETWEEN THE PIVOT TUBE AND THE ARM.

VEHICLE DESCRIPTION: MINI VANS BUILT FOR FLEET SALES ONLY. THE HEADLAMP MODULE DOES NOT IDENTIFY THE PARK LAMP AS "DRL" AS REQUIREMENT OF FMVSS 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

VEHICLE DESCRIPTION: PASSENGER VEHICLES. SOME FRONTAL (PASSENGER SIDE) AIR BAGS MAY NOT INFLATE PROPERLY.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE REAR SUSPENSION CROSSMEMBER MAY BE MISSING SPOT WELDS.

VEHICLE DESCRIPTION: ALL WHEEL DRIVE PASSENGER VEHICLES. LOCKUP OF THE TRANSFER CASE CAN OCCUR DUE TO INSUFFICIENT LUBRICATION.

VEHICLE DESCRIPTION: ALL WHEEL DRIVE PASSENGER VEHICLES. LOCKUP OF THE TRANSFER CASE CAN OCCUR DUE TO INSUFFICIENT LUBRICATION.

VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH INTEGRATED CHILD SEATS. THE SHOULDER HARNESS RESTRAINT ON THE INTEGRATED CHILD SEAT CAN BECOME DIFFICULT TO EXTRACT WHEN THE SAFETY BELT LATCH PLATE BECOMES CONTAMINATED.

VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH INTEGRATED CHILD SEATS. THE SHOULDER HARNESS RESTRAINT ON THE INTEGRATED CHILD SEAT CAN BECOME DIFFICULT TO EXTRACT WHEN THE SAFETY BELT LATCH PLATE BECOMES CONTAMINATED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. LOCKUP OF THE TRANSFER CASE CAN OCCUR DUE TO INSUFFICIENT LUBRICATION.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE BACK LIGHT BULBS FOR THE LIQUID CRYSTAL DISPLAY FOR THE GEAR SHIFT POSITION (PRNDL) AND THE ODOMETER WERE NOT PROPERLY INSTALLED.

VEHICLE DESCRIPTION: PASSENGER MINIVANS EQUIPPED WITH INTEGRATED CHILD SEATS. THE SHOULDER HARNESS RESTRAINT WEBBING WAS INCORRECTLY ROUTED AROUND THE METAL REINFORCEMENT BAR ON THESE SEATS.

VEHICLE DESCRIPTION: PASSENGER MINIVANS EQUIPPED WITH P215/65R15 GOODYEAR CONQUEST TIRES MOUNTED ON STEEL WHEEL. THE TIRES CAN EXPERIENCE A SUDDEN AIR PRESSURE LOSS WITHOUT WARNING.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.

VEHICLE DESCRIPTION: PASSENGER MINI-VANS. THE CENTER REAR SEAT, RIGHT OUTBOARD SIDE, SAFETY BELT ANCHOR HOOK CAN BECOME UNATTACHED FROM THE BODY ANCHOR POSITION.

VEHICLE DESCRIPTION: PASSENGER MINI-VANS. COVERS ON THE SOLID STALK MOUNTED SEAT BELT BUCKLES CAN BECOME DISLODGED CAUSING THE RELEASE BUTTON TO STICK INSIDE THE COVER. THE BUCKLE WOULD THEN BE ONLY PARTIALLY LATCHED.

VEHICLE DESCRIPTION: PASSENGER MINI-VANS. THE CENTER REAR SEAT, RIGHT OUTBOARD SIDE, SAFETY BELT ANCHOR HOOK CAN BECOME UNATTACHED FROM THE BODY ANCHOR POSITION.

VEHICLE DESCRIPTION: PASSENGER MINI-VANS. COVERS ON THE SOLID STALK MOUNTED SEAT BELT BUCKLES CAN BECOME DISLODGED CAUSING THE RELEASE BUTTON TO STICK INSIDE THE COVER. THE BUCKLE WOULD THEN BE ONLY PARTIALLY LATCHED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE STEERING COLUMN COUPLER CAN BECOME DISCONNECTED WHEN THE VEHICLE EXPERIENCES AN UNDERBODY IMPACT.

EXCESS LUBRICATION CAN CAUSE THE RUBBER DOOR LATCH SWITCH COVER TO DEFORM, AND THE DOOR LATCH SWITCH TO MALFUNCTION, SO THAT THE SHOULDER BELT ANCHORAGE WOULD REMAIN AT THE A-PILLAR WHEN THE DOOR WAS CLOSED.

THE GUIDE RAIL ON THE DRIVER'S SIDE CONTAINS A COVERED CABLE AND ALSO AN ANGLED BELT GUIDE AT THE TOP END OF THE WEBBING. THE COMBINATION OF THESE FACTORS CAN LEAD, OVER TIME, TO THE CABLE'S MOVEMENT EXERTING ABRADING FORCE TO THE LOWER EDGES OF THE CABLE'S CHAMBER, SUFFICIENT TO CAUSE THE CABLE TO DROP OUT OF THE CHAMBER WITH THE SHOULDER BELT ANCHORAGE BECOMING STUCK.

EXCESS LUBRICATION CAN CAUSE THE RUBBER DOOR LATCH SWITCH COVER TO DEFORM, AND THE DOOR LATCH SWITCH TO MALFUNCTION, SO THAT THE SHOULDER BELT ANCHORAGE WOULD REMAIN AT THE A-PILLAR WHEN THE DOOR WAS CLOSED.

THE GUIDE RAIL ON THE DRIVER'S SIDE CONTAINS A COVERED CABLE AND ALSO AN ANGLED BELT GUIDE AT THE TOP END OF THE WEBBING. THE COMBINATION OF THESE FACTORS CAN LEAD, OVER TIME, TO THE CABLE'S MOVEMENT EXERTING ABRADING FORCE TO THE LOWER EDGES OF THE CABLE'S CHAMBER, SUFFICIENT TO CAUSE THE CABLE TO DROP OUT OF THE CHAMBER WITH THE SHOULDER BELT ANCHORAGE BECOMING STUCK.

THE BOLTS USED TO ATTACH THE STRUT TO THE BODY AND THE REAR LIFTGATE CAN ACCUMULATE FATIGUE DAMAGE IF THREE FACTORS COMBINE. IF THE BOLT IS LOOSE, THE GAS STRUT IS OVER-PRESSURIZED, AND THE FREQUENCY OF OPENING AND CLOSING CYCLES IS HIGHER THAN FOR THE AVERAGE CUSTOMER, THE BOLT CAN FAIL.

THE BOLTS USED TO ATTACH THE STRUT TO THE BODY AND THE REAR LIFTGATE CAN ACCUMULATE FATIGUE DAMAGE IF THREE FACTORS COMBINE. IF THE BOLT IS LOOSE, THE GAS STRUT IS OVER-PRESSURIZED, AND THE FREQUENCY OF OPENING AND CLOSING CYCLES IS HIGHER THAN FOR THE AVERAGE CUSTOMER, THE BOLT CAN FAIL.

THE ELECTRICAL CIRCUIT DESIGN ALLOWS THE POTENTIAL FOR AN INADVERTENT AIR BAG DEPLOYMENT UPON VEHICLE IGNITION SHUT DOWN.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SECONDARY HOOD LATCH SPRING CAN DISENGAGE FROM ITS RETENTION HOLE IF THE HOOD IS SLAMMED SHUT.

THE LOWER SEAT BACK ATTACHING BOLT ON THE DRIVER'S SEAT CAN FAIL AND SEPARATE.

THE STEEL ROAD WHEELS WERE DAMAGED BY THE EQUIPMENT USED TO MATCH MOUNT THE WHEEL TO THE TIRE.

THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN.

THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN.

THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN.

THE FUEL AND REAR BRAKE TUBES CAN EXPERIENCE ACCELERATED CORROSION BETWEEN THE TUBES AND A RUBBER ISOLATOR.

THE ABS HYDRAULIC CONTROL UNIT CAN EXPERIENCE EXCESSIVE BRAKE ACTUATOR PISTON SEAL WEAR CAUSING PUMP-MOTOR DETERIORATION.

THE ABS HYDRAULIC CONTROL UNIT CAN EXPERIENCE EXCESSIVE BRAKE ACTUATOR PISTON SEAL WEAR CAUSING PUMP-MOTOR DETERIORATION.

THE BOLTS WHICH SECURE THE INTEGRATED CHILD SEAT MODULES TO THE SEAT FRAME CAN BREAK.

THE BOLTS WHICH SECURE THE INTEGRATED CHILD SEAT MODULES TO THE SEAT FRAME CAN BREAK.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

CORROSION OF THE ABS HYDRAULIC CONTROL UNIT CAN CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION.

THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.

THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.

IN CERTAIN VEHICLES, THE ENGINE CYLINDER HEAD OIL GALLEY PLUG DOES NOT SEAL PROPERLY AND ENGINE CYLINDER HEAD OIL IS NOT ADEQUATELY RETAINED.

IN CERTAIN VEHICLES, THE ENGINE CYLINDER HEAD OIL GALLEY PLUG DOES NOT SEAL PROPERLY AND ENGINE CYLINDER HEAD OIL IS NOT ADEQUATELY RETAINED.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

AN ENGINE WIRING HARNESS CAN SHORT CIRCUIT DUE TO CONTACT WITH THE EXHAUST GAS RECIRCULATION TUBE..

A STATIC ELECTRIC CHARGE CAN BUILD UP ON THE UNGROUNDED METAL SECTION OF THE FUEL FILLER TUBE.

A STATIC ELECTRIC CHARGE CAN BUILD UP ON THE UNGROUNDED METAL SECTION OF THE FUEL FILLER TUBE.

THE BOLTS WHICH SECURE THE REAR BENCH SEATS TO THE SEAT RISERS MAY BE EMBRITTLED AND FRACTURE.

THE BOLTS WHICH SECURE THE REAR BENCH SEATS TO THE SEAT RISERS MAY BE EMBRITTLED AND FRACTURE.

THE FUEL TANK ROLLOVER VALVE CAN ALLOW FUEL TO PASS INTO THE VAPOR CANISTER RESULTING IN THE POTENTIAL FOR FUEL LEAKAGE.

THE FUEL TANK ROLLOVER VALVE CAN ALLOW FUEL TO PASS INTO THE VAPOR CANISTER RESULTING IN THE POTENTIAL FOR FUEL LEAKAGE.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

THE SAFETY BELT ANCHORS (BUCKLE LOCK BARS) DO NOT MEET THE STATIC LOAD REQUIREMENTS OF FMVSS NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES."

THE REAR BRAKE HOSE MOUNTING BRACKET SCREWS CAN FAIL ALLOWING THE BRAKE HOSES TO MOVE OUT OF POSITION. THE UNRESTRAINED HOSES ARE THEN SUSCEPTIBLE TO DAMAGE WHICH COULD RESULT IN BRAKE FLUID LEAKAGE.

MOISTURE CAN GET INTO THE POWERTRAIN CONTROL MODULE (PCM) CAUSING DRIVEABILITY MALFUNCTIONS, INCLUDING STALLING.

THE ABS BRAKE MASTER CYLINDER REAR SEAL ALLOWS AIR TO ENTER THE BRAKE SYSTEM, CAUSING SPONGY BRAKES OR PARTIAL BRAKE SYSTEM LOSS.

THE 15 INCH WHEELS HAVE MALFORMED LUG NUT SEAT CONFIGURATION WHICH CAUSES POOR NUT-TO-WHEEL CONTACT AND CENTERING OF THE WHEEL DURING INSTALLATION.

THE 15 INCH WHEELS HAVE MALFORMED LUG NUT SEAT CONFIGURATION WHICH CAUSES POOR NUT-TO-WHEEL CONTACT AND CENTERING OF THE WHEEL DURING INSTALLATION.

FUEL TANK FLANGES WERE NOT BENT AS REQUIRED TO ALLOW THE SPECIFIED CLEARANCE FOR THE FUEL TANK MOUNTING STRAPS AND FUEL LINES AT THE TANK.

FUEL TANK FLANGES WERE NOT BENT AS REQUIRED TO ALLOW THE SPECIFIED CLEARANCE FOR THE FUEL TANK MOUNTING STRAPS AND FUEL LINES AT THE TANK.

THE AUTOMATIC SHOULDER RESTRAINT SYSTEMS CAN MALFUNCTION AND BECOME INOPERATIVE.

THE AUTOMATIC SHOULDER RESTRAINT SYSTEMS CAN MALFUNCTION AND BECOME INOPERATIVE.

PRESSURE REGULATOR INSTALLED IN THE FUEL SUPPLY PLUMBING SYSTEM LEAKS FUEL INTO THE ENGINE COMPARTMENT.

PRESSURE REGULATOR INSTALLED IN THE FUEL SUPPLY PLUMBING SYSTEM LEAKS FUEL INTO THE ENGINE COMPARTMENT.

THE ANTI-LOCK BRAKE SYSTEM HIGH PRESSURE PUMP MAY BE POROUS WHICH WILL RESULT IN BRAKE FLUID LEAKAGE.

THE ANTI-LOCK BRAKE SYSTEM HIGH PRESSURE PUMP MAY BE POROUS WHICH WILL RESULT IN BRAKE FLUID LEAKAGE.

THE ZINC PLATING OPERATION PERFORMED ON THE UPPER STEERING COLUMN SHAFT COUPLING BOLT CAUSED HYDROGEN EMBRITTLEMENT AND BREAKAGE OF THE BOLT.

THE ZINC PLATING OPERATION PERFORMED ON THE UPPER STEERING COLUMN SHAFT COUPLING BOLT CAUSED HYDROGEN EMBRITTLEMENT AND BREAKAGE OF THE BOLT.

THE ZINC PLATING OPERATION PERFORMED ON THE UPPER STEERING COLUMN SHAFT COUPLING BOLT CAUSED HYDROGEN EMBRITTLEMENT AND BREAKAGE OF THE BOLT.

THE ANTI-LOCK BRAKE SYSTEM HIGH PRESSURE HOSE MAY LEAK OR DETACH AT ITS CRIMPED END FITTING RESULTING IN THE DISCHARGE OF HYDRAULIC FLUID.

THE ANTI-LOCK BRAKE SYSTEM HIGH PRESSURE HOSE MAY LEAK OR DETACH AT ITS CRIMPED END FITTING RESULTING IN THE DISCHARGE OF HYDRAULIC FLUID.

THE STEERING WHEEL MAY CRACK AT ITS MOUNTING HUB WELD ATTACHMENT BECAUSE OF FATIGUE LOADING AND EVENTUALLY SEPARATE FROM THE HUB.

THE BRAKE PEDAL PAD ATTACHMENT TO THE PEDAL ARM MAY NOT HAVE ADEQUATE STRENGTH DUE TO MISLOCATION OF WELDS, AND COULD BREAK.

THE BRAKE PEDAL PAD ATTACHMENT TO THE PEDAL ARM MAY NOT HAVE ADEQUATE STRENGTH DUE TO MISLOCATION OF WELDS, AND COULD BREAK.

FRONT OUTBOARD SAFETY BELT MAY BECOME DIFFICULT TO LATCH AND OR UNLATCH DUE TO A WEBBING STIFFENER ENTERING THE BUCKLE HOUSING AND DISLODGING THE BUCKLE LATCH GUIDE.

REAR SUSPENSION TRAILING ARM-TO-HANGER BRACKET PIVOT BOLTS MAY FAIL FROM STRESS CORROSION CRACKING POSSIBLY CAUSED BY PROCESSING DEVIATIONS IN THE CONSTRUCTION OF THE PIVOT BOLT.

REAR SUSPENSION TRAILING ARM-TO-HANGER BRACKET PIVOT BOLTS MAY FAIL FROM STRESS CORROSION CRACKING POSSIBLY CAUSED BY PROCESSING DEVIATIONS IN THE CONSTRUCTION OF THE PIVOT BOLT.

INBOARD FRONT SEAT BELT BUCKLE ASSEMBLY STRAPS CAN SUFFER FATIGUE FAILURE OF THE STRAP NEAR ITS ANCHOR POSITION.

THE TWO AIR BAG SYSTEM FRONT IMPACT SENSORS MAY NOT BE SECURED TO THEIR MOUNTING BRACKETS.

INCORRECT SCREWS MAY HAVE BEEN USED IN INSTALLING THE LOAD SENSING BRAKE PROPORTIONING VALVE TO ITS BRACKET CAUSING THE CLAMPING LOAD TO BE LESS THAN INTENDED.

FRONT DISC BRAKE CALIPER GUIDE PIN BOLTS MAY NOT HAVE BEEN ADEQUATELY TORQUED AND COULD LOOSEN.

FRONT DISC BRAKE CALIPER GUIDE PIN BOLTS MAY NOT HAVE BEEN ADEQUATELY TORQUED AND COULD LOOSEN.

DILUTED PRIMER MAY HAVE BEEN USED ON THE WINDSHIELD OPENING FLANGES PRIOR TO WINDSHIELD GLASS INSTALLATION WHICH WOULD NOT PROVIDE THE RETENTION REQUIRED BY FMVSS 212.

OPERATION OF SUNROOF IN "NON-STANDARD" MANNER MAY CAUSE MALE HINGE DISENGAGEMENT FROM THE ROOF HINGE RECEIVER.

THE ENGINE VALVE COVER GASKET MAY DISLOCATE AND ALLOW AN ENGINE OIL LEAK AT THE GASKET.

THE ENGINE VALVE COVER GASKET MAY DISLOCATE AND ALLOW AN ENGINE OIL LEAK AT THE GASKET.

THE ENGINE VALVE COVER GASKET MAY DISLOCATE AND ALLOW AN ENGINE OIL LEAK AT THE GASKET.

THE ENGINE VALVE COVER GASKET MAY DISLOCATE AND ALLOW AN ENGINE OIL LEAK AT THE GASKET.

THE ENGINE VALVE COVER GASKET MAY DISLOCATE AND ALLOW AN ENGINE OIL LEAK AT THE GASKET.

THE ENGINE VALVE COVER GASKET MAY DISLOCATE AND ALLOW AN ENGINE OIL LEAK AT THE GASKET.

WIRING HARNESS FOR THE HEADLAMPS MAY BREAK DUE TO THE STRESS CREATED BY THE HEADLAMP POP UP DEVICES.

STEERING WHEEL HORN PADS DO NOT CONTAIN THE HORN SYMBOL DISPLAY AS REQUIRED BY FMVSS 101.

FRONT PASSENGER SEAT LAP BELT RETRACTOR, WHICH INCORPORATES A CHILD SEAT BELT LOCKING FEATURE, MAY MALFUNCTION.

FUEL LEAKAGE MAY OCCUR IN LOW AMBIENT TEMPERATURE OPERATION AT CONNECTIONS OF AN ENGINE COMPARTMENT FUEL SUPPLY HOSE TO THE PRESSURE REGULATOR AND TO THE FUEL RAIL.

FUEL LEAKAGE MAY OCCUR IN LOW AMBIENT TEMPERATURE OPERATION AT CONNECTIONS OF AN ENGINE COMPARTMENT FUEL SUPPLY HOSE TO THE PRESSURE REGULATOR AND TO THE FUEL RAIL.

A SERVICE REPLACEMENT DRIVERS SEAT CUSHION (MANUAL SEAT TYPE) MAY CONTAIN WRONG CUSHION WITH A BRACE THAT COULD INTERFERE WITH POWER SEAT ADJUSTER MECHANISM AND CAUSE STRESS ON THE FRAME.

FUEL TANKS MAY BE CONSTRUCTED OF IMPROPER MATERIAL.

FUEL TANKS MAY HAVE BEEN DAMAGED DURING TANK MANUFACTURE.

ENGINE COMPARTMENT WIRING HARNESS FUSIBLE LINK WIRES MAY BE TRAPPED UNDER THE SPEED CONTROL SERVO BRACKET.

BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.

BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.

BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.

BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.

BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.

FIRST REAR SEATS WERE INSTALLED WITH AN INCORRECT LEFT SIDE SEAT RISER WHICH CAUSES FAILURE TO COMPLY WITH THE SEAT AND SEAT BELT LOADING REQUIREMENTS OF FMVSS 207, SEATING SYSTEMS. CONSEQUENCE OF DEFECT: IF AN ACCIDENT OCCURRED, THE SEATS MAY BECOME DETACHED, CAUSING SERIOUS INJURIES TO ITS OCCUPANTS.

VANS EQUIPPED WITH THE OPTIONAL SUNSCREEN REAR GLASS WHICH HAS LESS THAN 70 PERCENT LUMINOUS TRANSMITTANCE AND DOES NOT HAVE A PASSENGER SIDE OUTSIDE REARVIEW MIRROR ARE NOT IN COMPLIANCE WITH FMVSS 111, REAR VIEW MIRRORS. CONSEQUENCE OF DEFECT: THE DRIVERS OF THESE VANS DO NOT HAVE THE MINIMUM FIELD OF VISION REQUIRED BY FMVSS 111. WITHOUT THIS MINIMUM FIELD OF VISION THE DRIVER CANNOT MANEUVER HIS VEHICLE SAFELY AND MAY CAUSE AN ACCIDENT.

AN ENGINE COMPARTMENT FUEL HOSE ROUTED TO THE FUEL SYSTEM PRESSURE REGULATOR MAY HAVE AN INADEQUATELY TIGHTENED HOSE CLAMP. CONSEQUENCE OF DEFECT: THE FUEL HOSE COULD LEAK AND RESULT IN AN ENGINE COMPARTMENT FIRE.

THE POTENTIAL FOR FUEL LEAKAGE EXISTS IN THE ENGINE COMPARTMENT AT THE FUEL RESERVOIR SEAM AND ITS HOSE CONNECTIONS. THE FUEL RESERVOIR IS A SILVER COLORED CAN MOUNTED TO THE AIR CLEANER.

THE POTENTIAL FOR FUEL LEAKAGE EXISTS IN THE ENGINE COMPARTMENT AT THE FUEL RESERVOIR SEAM AND ITS HOSE CONNECTIONS. THE FUEL RESERVOIR IS A SILVER COLORED CAN MOUNTED TO THE AIR CLEANER.

THE POTENTIAL FOR FUEL LEAKAGE EXISTS IN THE ENGINE COMPARTMENT AT THE FUEL RESERVOIR SEAM AND ITS HOSE CONNECTIONS. THE FUEL RESERVOIR IS A SILVER COLORED CAN MOUNTED TO THE AIR CLEANER.

THE POTENTIAL FOR FUEL LEAKAGE EXISTS IN THE ENGINE COMPARTMENT AT THE FUEL RESERVOIR SEAM AND ITS HOSE CONNECTIONS. THE FUEL RESERVOIR IS A SILVER COLORED CAN MOUNTED TO THE AIR CLEANER.

THE METAL FUEL SUPPLY TUBE MAY CRACK AT THE FUEL PUMP END DUE TO VIBRATION. THE CRACK MAY RESULT IN FUEL LEAKAGE. (THE FUEL SUPPLY TUBE CONNECTS THE FUEL PUMP TO THE FUEL FILTER.)

AN EMISSIONS SYSTEM VALVE MAY ALLOW AN OVERLY RICH MIXTURE (EXCESSIVE FUEL) IN THE ENGINE DURING DECELERATION. THE MIXTURE OF AIR AND EXCESSIVE FUEL CAN CAUSE THE ENGINE TO STALL WHILE STOPPING, COASTING, OR TURNING.

AN EMISSIONS SYSTEM VALVE MAY ALLOW AN OVERLY RICH MIXTURE (EXCESSIVE FUEL) IN THE ENGINE DURING DECELERATION. THE MIXTURE OF AIR AND EXCESSIVE FUEL CAN CAUSE THE ENGINE TO STALL WHILE STOPPING, COASTING, OR TURNING.

CERTAIN AFTERMARKET REPLACEMENT FUEL FILTERS, MODELS WIX FILTER PART NUMBERS 33576, 33577, 33734; NAPA FILTER PART NUMBERS 3576, 3577, 3734; AND CARQUEST FILTER PART NUMBERS 86576, 86577, 86734 USED ON 1996-2000 DAIMLERCHRYSLER TOWN & COUNTRY, DODGE CARAVAN, AND PLYMOUTH VOYAGER VEHICLES, CAN CAUSE THE FUEL LINES TO LEAK.

AFTERMARKET REPLACEMENT FUEL FILTERS MANUFACTURED BETWEEN SEPTEMBER 17, 2002, AND JANUARY 20, 2003, SOLD UNDER THE BRAND NAMES LISTED ABOVE. THE FILTER MAY EXPERIENCE MALFUNCTION OF THE QUICK CONNECTOR EITHER BLOCKING FUEL FLOW TO THE ENGINE OR CAUSING A FUEL LEAK. THIS DOES NOT INVOLVE ANY PRODUCTS MANUFACTURED BY THE DAIMLERCHRYSLER CORP. NOR ANY DAILMERCHRYSLER DEALERS.

VEHICLE DESCRIPTION: MULTIPURPOSE PASSENGER VEHICLES EQUIPPED WITH INTEGRAL CHILD SEATS. THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. ON THE INTEGRAL CHILD SEAT, THE SHOULDER BELTS RESTRAINING THE CHILD RETRACT AND LOCK IN PLACE AFTER THE BELT BUCKLE IS CONNECTED TO THE LATCH PLATE. THE LATCH PLATE MOVEMENT LOCKS THE BELTS TO MAKE SURE THE CHILD IS RESTRAINED IN THE CASE OF A VEHICLE CRASH.

VEHICLE DESCRIPTION: MULTIPURPOSE PASSENGER VEHICLES EQUIPPED WITH INTEGRAL CHILD SEATS. THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. ON THE INTEGRAL CHILD SEAT, THE SHOULDER BELTS RESTRAINING THE CHILD RETRACT AND LOCK IN PLACE AFTER THE BELT BUCKLE IS CONNECTED TO THE LATCH PLATE. THE LATCH PLATE MOVEMENT LOCKS THE BELTS TO MAKE SURE THE CHILD IS RESTRAINED IN THE CASE OF A VEHICLE CRASH.

CERTAIN AFTERMARKET REPLACEMENT FUEL FILTERS, MODELS WIX FILTER PART NUMBERS 33576, 33577, 33734; NAPA FILTER PART NUMBERS 3576, 3577, 3734; AND CARQUEST FILTER PART NUMBERS 86576, 86577, 86734 USED ON 1996-2000 DAIMLERCHRYSLER TOWN & COUNTRY, DODGE CARAVAN, AND PLYMOUTH VOYAGER VEHICLES, CAN CAUSE THE FUEL LINES TO LEAK.

AFTERMARKET REPLACEMENT FUEL FILTERS MANUFACTURED BETWEEN SEPTEMBER 17, 2002, AND JANUARY 20, 2003, SOLD UNDER THE BRAND NAMES LISTED ABOVE. THE FILTER MAY EXPERIENCE MALFUNCTION OF THE QUICK CONNECTOR EITHER BLOCKING FUEL FLOW TO THE ENGINE OR CAUSING A FUEL LEAK. THIS DOES NOT INVOLVE ANY PRODUCTS MANUFACTURED BY THE DAIMLERCHRYSLER CORP. NOR ANY DAILMERCHRYSLER DEALERS.

ROADWAY STONES MAY BECOME LODGED IN THE HEIGHT SENSING BRAKE PROPORTIONING VALVE. THIS MAY CAUSE THE PROPORTIONING VALVE TO FAIL. CONSEQUENCE OF DEFECT: PROPORTIONING VALVE MALFUNCTION RESULTS IN INCREASED STOPPING DISTANCES DURING HARD BRAKING WITH A LIGHT LOAD AND MAY CAUSE AN ACCIDENT.